Cisco 640-692 Online Practice Questions and Exam Preparation

Cisco 640-692 Online Questions & Answers

• Question 51:

  Which command is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?

  A. transport type all
  B. transport output all
  C. transport preferred all
  D. transport input all
  D. transport input all

• Question 52:

  Which command indicates the amount of memory (NVRAM, RAM, and flash) in a Cisco device?

  A. show diag
  B. show environment
  C. show inventory
  D. show version
  D. show version

• Question 53:

  Which two commands display the saved configuration file? (Choose two)

  A. show configuration
  B. show file system
  C. show running-config
  D. show startup-config
  A. show configuration
  D. show startup-config

• Question 54:

  Which two of the following are installed fiber-optic connectors? (Choose two)

  A. subscriber
  B. crossover
  C. multi-dimension
  D. Lucent
  A. subscriber
  D. Lucent

• Question 55:

  Which bits represent the boot field in the configuration register value?

  A. highest two bits
  B. highest four bits
  C. lowest two bits
  D. lowest four bits
  D. lowest four bits

• Question 56:

  The enable secret command is used to secure access to which CLI mode?

  A. global configuration mode
  B. privileged EXEC mode
  C. user EXEC mode
  D. auxiliary setup mode
  B. privileged EXEC mode

• Question 57:

  Refer to the exhibit.

  

  What can be determined about the router from the console output?

  A. No configuration file was found in NVRAM.
  B. No configuration file was found in flash.
  C. No configuration file was found in the PCMCIA card.
  D. Configuration file is normal and will load in 15 seconds.
  A. No configuration file was found in NVRAM.

• Question 58:

  Refer to the exhibit.

  

  Which three statements correctly describe Network Device A? (Choose three.)

  A. With a network wide mask of 255.255.255.128, each interface does not require an IP address.
  B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
  C. With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.
  D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
  E. With a network wide mask of 255.255.254.0, each interface does not require an IP address.
  B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
  D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
  E. With a network wide mask of 255.255.254.0, each interface does not require an IP address.

• Question 59:

  Which interface card is an encryption module?

  A. NME-VMSS-16
  B. NME-CUSP-522
  C. AIM-VPN/SSL-3
  D. M-1A-OC3-POM
  C. AIM-VPN/SSL-3

• Question 60:

  Which two commands are used to set the configuration register value? (Choose two)

  A. Router(config)#config-register 0x2102
  B. Router(config)#confreg 0x2102
  C. rommon>config-register 0x2102
  D. rommon>confreg 0x2102
  E. Router(config)#configuration-register 0x2102
  A. Router(config)#config-register 0x2102
  D. rommon>confreg 0x2102