Nokia 4A0-110 Online Practice Questions and Exam Preparation

Nokia 4A0-110 Online Questions & Answers

• Question 31:

  Which command is used to view alarms of all severity levels on the Alcatel 7x50?

  A. Show log log-id 99
  B. Show alarm
  C. Show log filter-id 1
  D. Show log log-id 100
  E. Show log 99
  A. Show log log-id 99

• Question 32:

  Two routers are physically connected to each other over Ethernet port 1/1/1. Review the configuration information below. What state should the OSPF neighbor be in?

  

  A. INIT
  B. EXCHANGE
  C. EXSTART
  D. FULL
  E. No OSPF neighbor
  D. FULL

• Question 33:

  Based on the show display below, what should be done to further trouble the LSP problem? Choose all valid actions.

  

  A. Check all the interface filters to make sure no LDP protocol is blocked
  B. Check all management filters to make sure no RSVP-TE protocol is blocked
  C. Verify all explicit hops are reachable via IGP
  D. Make sure MPLS is enabled on all appropriate interfaces
  E. Make sure LDP is enabled on all appropriate interfaces
  B. Check all management filters to make sure no RSVP-TE protocol is blocked
  C. Verify all explicit hops are reachable via IGP
  D. Make sure MPLS is enabled on all appropriate interfaces

• Question 34:

  Which files have to exist on Compact Flash 3 during system initialization on the Alcatel 7x50?

  A. iom.tim
  B. boot.ldr
  C. cpm.tim
  D. config.cfg
  E. bof.cfg
  B. boot.ldr
  E. bof.cfg

• Question 35:

  Which command can be used to view all interfaces configured under VPRN 300?

  A. Show router interfaces
  B. Show router interface vprn 300
  C. Show router 300 interfaces
  D. Show service vprn 300 interfaces
  E. Show service id 300 interfaces
  C. Show router 300 interfaces

• Question 36:

  VPRN 300 is configured on Node 3 and Node 4 with LDP and MP-BGP. No route can be found in the VPRN 300 routing table on both Nodes. What is the cause of the problem?

  

  A. No static route configured on Node 4
  B. No LDP defined in the VPRN configuration on both nodes
  C. VRF-target does not match on Node 3 and Node 4
  D. Route-distinguisher configuration is missing on Node 3 and Node 4
  E. Encapsulation type on the SAP does not match on Node 3 and Node 4
  D. Route-distinguisher configuration is missing on Node 3 and Node 4

• Question 37:

  Which command should be used to enable automatic synchronization for all software images and configuration on the Alcatel 7x50?

  A. Admin redundancy synchronization boot-env
  B. Admin redundancy synchronization config
  C. Configure redundancy synchronize boot-env
  D. Configure redundancy synchronize config
  E. It is enabled by default
  C. Configure redundancy synchronize boot-env

• Question 38:

  Two routers are physically connected to each other over Ethernet port 1/1/1. Review the configuration information shown below. What state should the OSPF neighbor be in?

  

  A. INIT
  B. EXCHANGE
  C. EXSTART
  D. FULL
  E. No OSPF neighbor
  E. No OSPF neighbor

• Question 39:

  Based on the following configuration, which of the following statements are true? Choose all that apply.

  

  A. No OPSF adjacency found on Node 1
  B. Full OSPF adjacency between Node-1 and Node-2
  C. Full OSPF adjacency between Node-1 and Node-3
  D. Full OSPF adjacency between Node-1 and Node-4
  E. OSPF is enabled on Node 1
  B. Full OSPF adjacency between Node-1 and Node-2
  E. OSPF is enabled on Node 1

• Question 40:

  Two routers are physically connected to each other with ISIS configured. No ISIS adjacency can be found on both routers. Ping works fine on the local and the remote interface addresses on both routers. Review the confguration information shown below. Which of the following statements best describe the cause of the problem? Select one answer only.

  

  A. The ISIS interface level configured does not match the ISIS level capability supported on the routers
  B. The ISIS authentication check is enabled but there is no authentication type and password configured
  C. ISIS Area addresses are not configured on both routers
  D. L1 wide Metrics are disabled on the routers
  E. ISIS Circuit id does not match on Node-1 and Node-2
  C. ISIS Area addresses are not configured on both routers