Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 71:

  A technician is adding the Virtual link Aggregation Control Protocol (VLACP) configuration to a Converged Campus Solution where all Ethernet Routing Switches (ERSs) are directly connected without intermediary WAN transport devices. What are two recommended configuration tasks? (Choose two.)

  A. Configure all links to use the same timeout value.
  B. For the Inter Switch Trunks (1ST) links, configure the long time-out value.
  C. For the SMLT links, configure the long timeout value.
  D. Configure all links to use a global reserved multicast MAC address for VLACP messages.
  B. For the Inter Switch Trunks (1ST) links, configure the long time-out value.
  D. Configure all links to use a global reserved multicast MAC address for VLACP messages.

• Question 72:

  The trace level 9 3 command accomplish?

  A. It captures BGP events at a terse level.
  B. It captures packets copied to the CPU at a verbose level.
  C. It shows CPU utilization.
  D. It captures RCC IP events at verbose level.
  B. It captures packets copied to the CPU at a verbose level.

• Question 73:

  The SNMP counters check for authorization failures and other types error conditions. Which of these SNMP error conditions is displayed in Enterprise Device Manager?

  A. PCAP packet capture counters
  B. In Bad Community Names counters
  C. Fan Failure packet counters
  D. Power Supply Failure packet counters
  D. Power Supply Failure packet counters

• Question 74:

  The edge has been configured; the core configuration can be verified. Which configuration is the last step in the verification process?

  A. MLT configuration check
  B. Ext CP limit configuration check
  C. SLPP configuration check
  D. VLACP configuration check
  C. SLPP configuration check

• Question 75:

  When configuring Ethernet Routing Switch (ERS) 8600 using the default interface, the attempt to load an ACLI configuration fails because the default interface is the CLI. How is the ACLI interface obtained?

  A. Change the interface type in the config.cfg file.
  B. Change the ACLI boot flag and save the boot configuration file.
  C. exits the CLI and chooses ACLI at the interface manager prompt.
  D. Use the abort command and enter "no" at the default interface prompt
  C. exits the CLI and chooses ACLI at the interface manager prompt.

• Question 76:

  To confirm that routed split Multi-Link Trunking (RSMLT0 will work on a set of VLANs, which network design aspect should be considered?

  A. RSMLT is enabled on each SMLT VLAN on which the function is required.
  B. RSMLT is enabled on the VLAN group.
  C. Router 1 always owns the network.
  D. RSMLT is enabled on all SMLT VLANs.
  A. RSMLT is enabled on each SMLT VLAN on which the function is required.

• Question 77:

  Ethernet Routing Switch (ERS) 5500 supports a resilient stacking architecture using FAST Stack technology with this stacking capability, what is the total stacking bandwidth for a full stack of eight switches?

  A. 400 Gbps
  B. 640 Gbps
  C. 720 Gbps
  D. 1.15 Tbps
  B. 640 Gbps

• Question 78:

  A switch duster core composed of two Ethernet Routing Switch (ERS) 8600 switches has been property configured to supports new edge switch stack 802.1Q correctly configured on the edge switch stack. What will the switch core do with packets arriving from this edge stack?

  A. It will forward the packets to the Switch CPU.
  B. it will place them m the data VLAN.
  C. Pace them in the default VLAN (VLAN1)
  D. It will discard the packets
  A. It will forward the packets to the Switch CPU.
  B. it will place them m the data VLAN.

• Question 79:

  When configuring an Ethernet Routing Switch (ERS) 8600 redundant Installation for warm standby, which protocol is used to give the fastest recalculation of large layer 3 topology by the standby CPU, after a Master CPU failure?

  A. STP
  B. Rip
  C. OSPF
  D. BGP
  C. OSPF

• Question 80:

  A campus network has been established with four Ethernet Routing Switch (ERS) 8600 switches in a switch cluster, two pairs with an Inter Switch Trunks (1ST) running Split Multi-Link Trunk (SMLT) and Routed Split Multi-Link Trunking (RSMLT). The traffic filters are required to block specific source IP addresses to be forwarded through the core.

  How should these filters be set up?

  A. Configure the filters on the 1ST first before any other ports.
  B. Apply the filters to all ports that receive traffic from outside the immediate switch cluster.
  C. Configure the filters on the ports first and then the 1ST.
  D. Apply the filters to the edge switches and never on the switch cluster ERS 8600 switches.
  D. Apply the filters to the edge switches and never on the switch cluster ERS 8600 switches.