Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 61:

  In a newly installed network the port LED on an Ethernet Routing Switch (ERS) 5500 is amber, not green. What does this mean?

  A. The port is set to operate at 10 Mbps.
  B. The port is set to operate at 100 Mbps.
  C. It indicates that there is a transmit fault.
  D. It indicates that the port is administratively disabled.
  D. It indicates that the port is administratively disabled.

• Question 62:

  Avaya recommends using RSMLT edge in place of VRRP with Backup Master, when available what are two valid reasons for using RSMLT edge? (Choose two)

  A. the VRRP hold down timer cannot be set high enough to update the complete routing table when Layer 2 access requirements are high.
  B. RSMLT edge provides support for application where more than 255 redundant default gateways (VRRP limit) need to be provided.
  C. RSMLT edge allows the cluster to be configured to discard untagged frames in 1ST and SMLT ports.
  D. RSMLT edge is easier to configure and lightens the CPU load,
  E. RSML T dynamically balances the CPU load across the switch cluster.
  B. RSMLT edge provides support for application where more than 255 redundant default gateways (VRRP limit) need to be provided.
  D. RSMLT edge is easier to configure and lightens the CPU load,

• Question 63:

  Before enabling IP Source through Device Manager, which two conditions must be met on the system?

  A. Dynamic Host Control Protocol (DHCP) snooping enabled globally.
  B. EAPOL must be enabled.
  C. The bsSourceGuardConfigMode MIB object must be removed.
  D. The port is an untrusted DHCP snooping and dynamic ARP Inspection port.
  A. Dynamic Host Control Protocol (DHCP) snooping enabled globally.
  D. The port is an untrusted DHCP snooping and dynamic ARP Inspection port.

• Question 64:

  When configuring link aggregation, a technician created a Distributed Multi-Link Trunk (DMLT) group on the Edge switch to the switch cluster core. What gets distributed?

  A. Access ports
  B. Discard Looped Frames
  C. Spanning Tree Enable
  D. LACP Enable
  A. Access ports

• Question 65:

  Which commands will configure the labeled Ethernet ports appropriately?

  

  A. Config Ethernet 3/1 enable-diffserv trueconfig Ethernet 1/1 access-diffserv true
  B. Config Ethernet 3/1 enable-diffserv trueconfig Ethernet 1/1 access-diffserv false
  C. Config Ethernet 1/1, 3/1 enable-diffserv trueconfig Ethernet 1/1 access-diffserv true
  D. Config Ethernet 3/1 enable-diffserv trueconfig Ethernet 3/1 access- diffserv true
  C. Config Ethernet 1/1, 3/1 enable-diffserv trueconfig Ethernet 1/1 access-diffserv true

• Question 66:

  Routed Split Multilinking Trunking (RSMLT) is a way to ensure that traffic can be routed off the VLAN by adding router redundancy. RSMLT is configured on which Ethernet Routing Switch (ERS) configuration component?

  A. an OSPF router
  B. a core switch port
  C. a VLAN
  D. an SMLT
  A. an OSPF router

• Question 67:

  

  Which two pairs of commands will configure spanning tree on the edge switch? (Choose two)

  A. 5520-24T (config) # interface fastethernet 25-265520-24T (corrfig-if) # spanning-tree learning fast
  B. 5520-24T (config) # interface fastethernet 25-265520-24T (config-if) # spanning tree learning disable
  C. 5520-24T (config) # interface fastethernet 1-205520-24T (config-if) # spanning tree learning disable
  D. 5520-24T (config) # interface fastethernet 1-205520-24T (config-if) # spanning-tree learning fast
  A. 5520-24T (config) # interface fastethernet 25-265520-24T (corrfig-if) # spanning-tree learning fast
  C. 5520-24T (config) # interface fastethernet 1-205520-24T (config-if) # spanning tree learning disable

• Question 68:

  Click the exhibit button.

  

  SLPP has just been enabled on both core switches.

  Based on the network diagram and console output from the core 1 Ethernet Routing Switch (ERS) B600 shown in the exhibit, what is the configuration error on the edge switch?

  A. The edge switch spanning-trcc has not been configured.
  B. The edge switch access port rate limiting has not been configured.
  C. The edge MLT has not been configured correctly.
  D. The edge VUXNs has not been configured.
  A. The edge switch spanning-trcc has not been configured.

• Question 69:

  After issuing a show mit ist stats (CLI) or show ist stat (ACLI) command, it is determined that running type is normal MLT and not Inter Switch Trunks (IST). Which are two causes of the 1ST not running properly? (Choose two.)

  A. The 1ST is not enabled on both switches.
  B. The MLT ID does not match on both switches.
  C. The peer IP address is not the address of the peer switch 1ST VLAN
  D. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.
  A. The 1ST is not enabled on both switches.
  C. The peer IP address is not the address of the peer switch 1ST VLAN

• Question 70:

  A technician is adding the Virtual Link Aggregation Control Protocol (VLACP) configuration ID a Converged Campus Solution where all Ethernet Routing switches (ERSs) are directly connected without intermediary WAN transport devices. What are two key configuration tasks? (Choose two)

  A. configure all links to use the default multicast MAC address for VLACP messages
  B. For the 1ST links, configure the long timeout value
  C. For the SMLT links, configure the long timeout value
  D. Configure all links to use a unique reserved multicast MAC address for VLACP messages
  B. For the 1ST links, configure the long timeout value
  D. Configure all links to use a unique reserved multicast MAC address for VLACP messages