Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 51:

  Based on the command line output shown in the exhibit, how many Gigabit Ethernet ports are available on this Ethernet Routing Switch (ERS) 8600?

  

  B. 24
  C. 26
  D. 28
  C. 26

• Question 52:

  Which statement describes how to configure Simple Loop Prevention protocol (SLPP) Rx?

  A. SLPP is configured on the edge switch ports that connect to the core switch cluster.
  B. SLPP is configured on the core switch cluster ports that connect to the edge switch.
  C. SLPP is configured on the Inter Switch Trunk (1ST) ports of the core switch cluster.
  D. SLPP is configured on the uplink ports of both the core switch cluster and the edge switch
  D. SLPP is configured on the uplink ports of both the core switch cluster and the edge switch

• Question 53:

  A technician has implemented Routed Split Multi-Link Trunking (RSMI I) edge design. After recovering power outage some clients could not communicate. It has been determined that only one of the core RSMLT switches has recovered. What should have been done to prevent the loss communications?

  A. Turn off the HoldDown timer.
  B. Increase the Holdup timer to 9999.
  C. Clear the peer IP and MAC addresses
  D. Set the VLAN to copy RSMLT info from a similarly configured VLAN.
  B. Increase the Holdup timer to 9999.

• Question 54:

  Where is the rate-limit feature of the Converged Campus architecture limited?

  A. uplink ports on the core switches
  B. access ports on the edge switches
  C. inter Switch Trunk ports on the core switches
  D. uplink ports on the edge switches
  A. uplink ports on the core switches
  B. access ports on the edge switches
  D. uplink ports on the edge switches

• Question 55:

  When multiple VLANs are used, Dynamic Host Control protocol (DHCP) relay is required to get the DHCP information from the end user VLAN to the DHCP server. Which statement about how to enable DHCP relay for a VLAN is true?

  A. The physical VLAN IP address is used as the DHCP relay agent.
  B. The IP address of the DHCP relay agent is used.
  C. The IP address of the core server VLAN is used
  D. The virtual VLAN IP address is used as the DHCP relay agent.
  D. The virtual VLAN IP address is used as the DHCP relay agent.

• Question 56:

  A technician has installed a license file on the Ethernet routing switch (ERS) 8800 and rebooted, but cannot configure the associated licensed features. it has been determined that license did not load properly at booyup time. Which two must be verified?

  A. The switch is at the current release.
  B. The license filename contains valid characters.
  C. The license file is stored in the flash directory
  D. The appropriate license level has been obtained.
  E. The license file has .dat extension.
  B. The license filename contains valid characters.
  E. The license file has .dat extension.

• Question 57:

  A customer has implemented an ERS 8000 solution and deployed the configuration and Orchestration Manager (COM). Which tool from within COM is used to set up and manage spanning tree groups?

  A. Global Manager
  B. VLAN Manager
  C. Security Manager
  D. VSN Manager
  B. VLAN Manager

• Question 58:

  Syslog in the Ethernet Routing Switch (ERS) 8600 allows the mapping of ERS 8600 errors to be Specified to the facility Local 0 Local 7. What is another piece of information that syslog provides?

  A. severity level
  B. message frequency
  C. syslog table location
  D. system status
  A. severity level

• Question 59:

  The User interface (Ul) button on the Ethernet Routing Switch (ERS) 6500 can be used to temporarily reset a switch to the default IP address. Which two statements are true about the default IP address set via the Ul button? (Choose two)

  A. The default IP address overrides the IP address currently in use by the switch stack.
  B. The default IP address overwrites the "configured" IP address settings that are set via console. CLI or Web.
  C. the default IP address changes if there is a change in the state of the switch, such as if the switch joins or leaves a stack.
  D. the default IP address is saved in NVRAM across resets of the switch/stack.
  A. The default IP address overrides the IP address currently in use by the switch stack.
  B. The default IP address overwrites the "configured" IP address settings that are set via console. CLI or Web.

• Question 60:

  OSPF computes the shortest path to destination subnets, whereas, IS-IS, as used with SPBM works differently. Which parameter does IS-IS use to compute the path?

  A. Customer MACs
  B. Backbone MGIDs
  C. VLAN MAC IDs
  D. Backbone nodal MAC addresses
  D. Backbone nodal MAC addresses