Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 41:

  A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 lo a core pair of ERS 8600 switches. Which statement about the correct uplink configuration is true?

  A. Distribute uplinks across different ERS 5500 switches in the stack.
  B. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure
  C. Use unique MLT IDS for each stack of edge ERS 5500 switches
  D. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.
  A. Distribute uplinks across different ERS 5500 switches in the stack.

• Question 42:

  Click on the exhibit button

  

  After checking the VLAN configuration using the show vlan info basic and the show vlan info port commands, there are no ACTIVE MEMBER ports for VLM4-50. What is causing this problem?

  A. The ports have not been configured as active for this VLAN
  B. AppleTalk Protocol VLANs do not have ACTIVE MEMBERS
  C. The default setting for this type of VLAN is potential and no AppleTalk traffic has entered any of these ports
  D. There are no devices connected to these ports.
  C. The default setting for this type of VLAN is potential and no AppleTalk traffic has entered any of these ports

• Question 43:

  A technician is setting up switch clustering using Split Multi-Link Trunking (SMLT). Which link is configured between the SMLT cluster switches?

  A. Inter-Switch Trunk (IST)
  B. Multi link Trunk (MLT)
  C. Split Multi Link Trunk (SMLT)
  D. LAG Trunk
  A. Inter-Switch Trunk (IST)

• Question 44:

  A switch with Simple Loop Prevention Protocol (SLPP) did not detect a loop. What are two reasons this occurred? (Choose two)

  A. SLPP was not globally enabled
  B. A premier License for SLPP is needed.
  C. the VLAN where the loop originated to the SLPP transmitting list was not added.
  D. Extended CP limit on the transmitting port was not configured.
  A. SLPP was not globally enabled
  C. the VLAN where the loop originated to the SLPP transmitting list was not added.

• Question 45:

  When multiple VLANs are used, Dynamic Host Control Protocol (DHCP) relay is required to get the DHCP information from the end user VLAN DHCP server.

  Which statement about how to enable DHCP relay is true?

  A. The physical VLAN IP address is configured as the DHCP relay agent on each VLAN requiring a DHCP relay.
  B. The IP address of the DHCP server is configured as the relay agent globally on all switches that do not directly attach to the DHCP server.
  C. The MAC address of the DHCP server configured as the DHCP relay agent on each VLAN requiring the DHCP relay agent.
  D. The DHCP relay is configured globally and is automatically applied to all VLANs requiring a DHCP relay.
  A. The physical VLAN IP address is configured as the DHCP relay agent on each VLAN requiring a DHCP relay.

• Question 46:

  A university campus network consists of an Ethernet Routing Switch (ERS) 8000 and Ethernet switches. Recently they implemented Routed Split Multi-Link g (RSMLT) over a split Multi- Link Trunk (SMLT) configuration. What is the advantage of implementing RSMLT over SMLT?

  A. RSMLT increases the distance of the SMLT core.
  B. RSMLT achieves better data distribution across the SMLT.
  C. RSMLT extends fast failover benefits to the routed portion of the network.
  D. RSMLT allows the addition new users in a separate building.
  C. RSMLT extends fast failover benefits to the routed portion of the network.

• Question 47:

  The ERS 8000 backplane hosts an EEPROM for storage of up to 4096 MAC addresses. The MAC addresses are automatically used up as they are assigned to which three of the following?

  A. Switch physical ports
  B. Multi-Link Trunking ports.
  C. Multi-Link Trunking groups.
  D. IPX interfaces.
  E. VLANs.
  A. Switch physical ports
  C. Multi-Link Trunking groups.
  E. VLANs.

• Question 48:

  In Ethernet Routing Switch (ERS) 5600 switch was added into the existing ERS 5500 stack, but ft did not form a proper stack. Which statement describes the problem?

  A. The ERS 5600 was set as the Base Unit.
  B. The stack was reset for a change in Base Unit to take effect.
  C. The mode parameter on the ERS 5600 switch was set to Mixed Mode.
  D. The ERS 5500 was set as the Base Unit.
  D. The ERS 5500 was set as the Base Unit.

• Question 49:

  A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24 network, but does not have a console cable available. Which statement is correct?

  A. The switch will first attempt to use BootP to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP.
  B. The customer can set the switch to use the temporary address of 192.168.192.168 by pressing the User Interface button on the front of the ERS 2550T
  C. To communicate with an ERS 2550T the IP address must first be set though the console interface.
  D. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address
  D. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address

• Question 50:

  Traceout allows a route to be traced to a network using an Ethernet Routing Switch (ERS) 8600 CLI command. In the command output, the possible range of `w' values is 1-255. The `w' value represents wait time for what?

  A. Start of command execution
  B. Time to live
  C. Per probe
  D. Completion of traceout report
  C. Per probe