Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 31:

  An engineer needs to assign an IP address of 172 25 10.31 for out of band management of an Ethernet Routing switch (ERS) 8600 switch a subnet mask of 255.255.255.192. Which command line interface (CLI) command should the engineer use?

  A. ERS8600:5# config bootconfig set ip 172.26.10 36/26
  B. ERS8800:5 # config bootconfig set ip 172.25.10 36/27
  C. ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/27
  D. ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/26
  D. ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/26

• Question 32:

  The technician is setting up an Ethernet Routing Switch (ERS) 8300 switch for QoS. It has been determined that unimportant traffic will be marked on the edge of the network with a default IEEE 802.Ip setting off 0. Since the ERS 8300 is in the core, the traffic must be identified with the proper class of service. The technician has used JDM to look at the TrafficClass Map with the shown in the exhibit.

  

  What can be determined from the ERS 8300 parameters?

  A. The ERS 8300 mapping has been altered since the IEEE 802.lp settings do not map directly to the same Traffic Class.
  B. The ERS 8300 mapping is normal and should be left as is
  C. The ERS 8300 mapping will push the IEEE 802. ip setting off 0 above the network control traffic.
  D. The ERS 8300 as a core device will not use the IEEE 802.1 p to Traffic Class Map for this application.
  A. The ERS 8300 mapping has been altered since the IEEE 802.lp settings do not map directly to the same Traffic Class.

• Question 33:

  The Ethernet Routing Switch (ERS) 8600 switch includes a means to fine tune the memory resources by allowing the record allocations to be allowed. An ERS 8600 running Release 5.0 needs to be configured to be optimized for multicast traffic.

  Which command alters the ERS 8600 to increases the default allocation of Multicast by 50 percent?

  A. Config sys set record record reserve MGID + 50
  B. Config sys set max-vlan-resource-reservation 4096
  C. Config sys set show sys mgid usage
  D. Config sys set multicast-resource-reservation 3073
  D. Config sys set multicast-resource-reservation 3073

• Question 34:

  Routed Split Multi-Link Trunking (RSMLT) is a way to ensure that traffic can be routed off the VLAN by adding router redundancy. When configuring the Ethernet Routing Switch (ERS) core switches, where is RSMLT configured?

  A. An OSPF protocol
  B. A core switch port
  C. A VLAN
  D. An edge switch port
  A. An OSPF protocol

• Question 35:

  A customer has security concerns with the current RADIUS authentication implementation and is asking to change all authentication requests from the ERS 8000 to be directed to their TACACS+ server. What two differences exist between the authentication requests used by RADIUS and TACACS+ that would you cause this concern for the customer? (Choose two)

  A. TACACS+ is a TCP-based protocol.
  B. RADIUS does not support AES encryption.
  C. TACACS+ uses full packet encryption.
  D. RADIUS uses clear passwords.
  A. TACACS+ is a TCP-based protocol.
  C. TACACS+ uses full packet encryption.

• Question 36:

  While troubleshooting a MultiLink Trunking (MLT) and split MultiLink Trunking (SMLT) network a need arises to determine which link packets are traversing. Which feature should be used to facilitate the troubleshooting?

  A. Ping Trace
  B. Ping Snoop
  C. Snoop Trace
  D. Trace Route
  B. Ping Snoop

• Question 37:

  Which statement describe step in provisioning SPBM in an Enterprise network?

  A. IP addresses on the core links.
  B. Enable SPBM and IS -IS globally on all nodes and on the core facing links.
  C. Configure the MAC table.
  D. Configure L2 and L3 VSNs on the core SPBM nodes.
  B. Enable SPBM and IS -IS globally on all nodes and on the core facing links.

• Question 38:

  In a multicast campus, when should an ERS 8600 PIM interface be configured to run in passive mode?

  A. When the interface is used as an edge interface and is aggregating traffic.
  B. When the interface is used as a core interface and needs to limit PIM messages to reduce the system load.
  C. When there are no unicast routing paths.
  D. When more than one unicast routing protocol is in use.
  A. When the interface is used as an edge interface and is aggregating traffic.

• Question 39:

  After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI commands is used to find that the switch not recognize the XFPs. Which other method can be used to view the XFP compatibility?

  A. Check for port alarms
  B. Show DWDM-XFP {default}.
  C. Use the monitor sys tech info command to monitor for any changes in compatibility.
  D. Use enterprise Device Manager and select the Edit, Port, General tab from the navigation pane to display any XFP compatibility issues.
  D. Use enterprise Device Manager and select the Edit, Port, General tab from the navigation pane to display any XFP compatibility issues.

• Question 40:

  IPFIX protocol used for the export of flow information from traffic observed on a switch. Which three statements are true for the functioning of the IPIX protocol? (Choose three)

  A. The IPIX exporter handles sending packets to the collectors.
  B. ACls can be used to configure IPFIX on a per port/slot basis.
  C. The IPMX information cannot be exported to a 3rd-party application.
  D. IPFIX requires dual CPUs installed for the ERS 8000.
  A. The IPIX exporter handles sending packets to the collectors.
  B. ACls can be used to configure IPFIX on a per port/slot basis.