Cisco 352-011 Online Practice Questions and Exam Preparation

Cisco 352-011 Online Questions & Answers

• Question 11:

  When designing a network .Which method can be used to control the exit point for traffic an autonomous system, at the layer 3 control plane?

  A. Prepending AS path.
  B. Tuning the multi-exit discriminator.
  C. Setting the site of Origin extended community.
  D. Tuning the metric of the under-tying IGP.
  D. Tuning the metric of the under-tying IGP.

• Question 12:

  Which two options are design considerations when introducing FCoE into an existing network? (Choose two)

  A. The FCoE QoS markings may overlap with call signaling QoS markings
  B. Optical cabling is needed to transmit FCoE traffic between a server and its directly connected Ethernet switch
  C. The existing network must support a MTU of 3280 bytes
  D. Twinaxial cabling can be used to transmit FCoE traffic between a server and its directly connected Ethernet switch, if it is less than 10 meters
  E. All the servers in the data center must be retrofitted with converged Network Adapters
  A. The FCoE QoS markings may overlap with call signaling QoS markings
  E. All the servers in the data center must be retrofitted with converged Network Adapters

• Question 13:

  Refer to the exhibit.

  

  Which routing solution is the most scalable to connect the branches to the HQ and to connect the branches together over the internet using DMVPN?

  A. EIGRP
  B. EIGRP with the branch routers setup as stubs
  C. OSPF with each branch router as an ABR
  D. IS-IS L2 in all locations
  E. OSPF Area 0 in all locations
  B. EIGRP with the branch routers setup as stubs

• Question 14:

  In an Ethernet link containing five routers with OSPF network interface type configured as broadcast, how many OSPF adjacencies are established on this Ethernet link?

  A. 7
  B. 5
  C. 10
  D. 20
  E. 6
  A. 7

• Question 15:

  After a large EIGRP network had automatic summarization enabled throughout, it started experiencing routing loops. Which action should you take to quickly resolve the routing loops yet to perform summarization?

  A. Redistribute connected routes at major IP networks boundaries
  B. Redesign the IP addressing scheme
  C. Increase the AD of the automatically summarized routes D. Replace the automatic summarization with more specific summary routes
  D

• Question 16:

  Which statement about TAP and TUN devices, which are used in a Linux/KVM cloud deployment model, is true?

  A. TUN is for handling IP packets, but TAP is for handling Ethernet frames
  B. TUN is for handling Ethernet frames, but TAP is for handling IP packets
  C. TUN is for tunneling IP packets, but TAP is for tapping IP packets
  D. TUN is for tunneling Ethernet frames, but TAP is for tapping Ethernet frames
  A. TUN is for handling IP packets, but TAP is for handling Ethernet frames

• Question 17:

  You work as a network designer for a company that is replacing their Frame Relay WAN with an MPLS VPN service, where the PE-to-CE routing protocol is BGP. The company has 3000 routes in their distribution routers, and they would like to advertise their access routers through the MPLS network. Their service provider, however, only supports 1000 prefixes per VRF. Which two design solutions can be applied to ensure that your access routers will be able to reach all devices in your network? (Choose two.)

  A. Configure the distribution routers to send a default route to the MPLS network
  B. Configure null routes and aggregate routes for the prefixes in your network on the distribution routers
  C. Summarize the routes on MPLS WAN interfaces of the distribution routers
  D. Use prefix lists on the distribution routers to control which routes are sent to MPLS network
  E. Configure the access routers to send a default route to the MPLS network
  A. Configure the distribution routers to send a default route to the MPLS network
  C. Summarize the routes on MPLS WAN interfaces of the distribution routers

• Question 18:

  Which option is a design consideration when using routers in a distributed hardware architecture?

  A. Routing information is stored in the RIB and the FIB makes forwarding decisions as programmed on the line card hardware
  B. After a link failure occurs in the core, the RIB continues to forward the traffic while FIB convergence is in progress
  C. BGP routes are stored in the RIB and IGP routes are stored in the FIB
  D. IP routes are stored in the RIB and MPLS labels are stored in the FIB
  A. Routing information is stored in the RIB and the FIB makes forwarding decisions as programmed on the line card hardware

• Question 19:

  Which main IoT migration aspect should be reviewed for a manufacturing plant?

  A. Sensors
  B. Security
  C. Applications
  D. Wi-Fi Infrastructure
  E. Ethernet Switches
  A. Sensors

• Question 20:

  You have been asked to design a high -density wireless network for a university campus. Which two principles would you apply in order to maximize the wireless network capacity? (Choose two.)

  A. Implement a four-channel design on 2.4 GHz to increase the number of available channels.
  B. Make use of the 5-GHz band to reduce the spectrum utilization on 2.4 GHz when dual- band clients are used.
  C. Choose a high minimum data rate to reduce the dory cycle.
  D. Enable 802.11n channel bonding both 2.4 GHz and 5 GHz to increase the aggregated cell throughput.
  E. Increase the number of SSIDs to load-balance the client traffic.
  C. Choose a high minimum data rate to reduce the dory cycle.
  E. Increase the number of SSIDs to load-balance the client traffic.