Cisco 350-801 Online Practice Questions and Exam Preparation

Cisco 350-801 Online Questions & Answers

• Question 401:

  An engineer troubleshoots outbound can failure on an ISDN-PRI circuit. The engineer is suspecting the 'Incomplete Destination".

  Which debugs or commands are run in the voice gateway to troubleshoot the issue?

  A. debug isdn q921 term mon
  B. debug voip ecapi inout show controller ti
  C. debug isdn q931 show isdn status
  D. debug isdn q921 debug voip ecapi inout
  C. debug isdn q931 show isdn status

  ---

  Explanation

  The engineer should run the following debugs or commands in the voice gateway to troubleshoot the issue: debug isdn q931 - This debug will show the ISDN Q.931 messages that are being exchanged between the voice gateway and the ISDN switch. This can be used to identify the cause of the "Incomplete Destination" error. show isdn status - This command will show the status of the ISDN PRI circuit. This can be used to verify that the circuit is up and running. The other options are not correct. The debug isdn q921 command will show the ISDN Q.921 messages that are being exchanged between the voice gateway and the ISDN switch. This is not necessary for troubleshooting the issue. The term mon command will show the terminal monitor output. This is not necessary for troubleshooting the issue. The debug voip ecapi inout command will show the VoIP ECAP messages that are being exchanged between the voice gateway and the VoIP server. This is not necessary for troubleshooting the issue. The show controller ti command will show the status of the T1 controller. This is not necessary for troubleshooting the issue.

• Question 402:

  A Cisco collaboration engineer is troubleshooting unexpected SIP call disconnect.

  Which three responses corresponding to the 5xx range? (Choose Three)

  A. Forbidden
  B. Unauthorized
  C. Request timeout
  D. Service unavailable
  E. Bad gateway
  F. Internal server error
  D. Service unavailable
  E. Bad gateway
  F. Internal server error

• Question 403:

  An engineer must create a route pattern for a SIP trunk with the pattern named Unity_Con_SIP_Trunk and a voicemail pilot number 8000/< None > in Cisco Unity Connection.

  Which value must the engineer enter for the Gateway/Route List field?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  D. Option D

• Question 404:

  A user dials 9011841234567 to reach Vietnam.

  Which steps send the call to the PSTN provider as 011841234567?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  A. Option A

• Question 405:

  Which action prevents toll fraud in Cisco Unified Communications Manager?

  A. Implement toll fraud restriction in the Cisco IOS router.
  B. Implement route patterns in Cisco Unified CM.
  C. Allow off-net to off-net transfers.
  D. Configure ad hoc conference restriction.
  D. Configure ad hoc conference restriction.

  ---

  Explanation

  References:

  https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/107626-cme-toll-fraud.html

• Question 406:

  DRAG DROP

  An engineer must add a new user account and mailbox in Cisco Unity Connection. Drag and drop the configuration steps from the left into the correct order on the right.

  Select and Place:

  

  

• Question 407:

  Refer to the exhibit.

  

  Unanswered calls do not reach the voicemail associated with the phones. Instead, callers receive the default greeting.

  Which action fixes the configuration?

  A. Review the conversation manager logs on Cisco Unity Connection.
  B. Check the box "Redirecting Diversion Header Delivery - Outbound", then reset the trunk.
  C. Reboot Cisco Unity Connection.
  D. Check the box "Redirecting Diversion Header Delivery - Outbound".
  B. Check the box "Redirecting Diversion Header Delivery - Outbound", then reset the trunk.

• Question 408:

  An administrator troubleshoots call flows and suspects that there are issues with the dial plan.

  Which tool enables a quick analysis of the dial plan and provides call flows of dialed digits?

  A. Dial Plan Analyzer
  B. Dialed Number Analyzer
  C. Cisco Dial Plan Analyzer
  D. Digit Analysis Analyzer
  B. Dialed Number Analyzer

  ---

  Explanation

  References:

  https://aurus5.com/blog/cisco/configuring-dialedconfiguring-dialed-number-analyzer-in-cucm/

• Question 409:

  Refer to the exhibit

  

  The SDP offer/answer has been completed successfully but there is no DTMF when users press keys.

  What is the cause of the issue?

  A. DTMF was negotiated properly in these messages.
  B. G.729 rather than G.711ulaw was negotiated.
  C. Payload type 110 was negotiated rather than type 101.
  D. DTMF was not negotiated on the call.
  D. DTMF was not negotiated on the call.

  ---

  Explanation

  https://www.ciscolive.com/c/dam/r/ciscolive/us/docs/2018/pdf/BRKUCC-2006.pdf

  [page 47]

• Question 410:

  An engineer must configure DTMF relay on a Cisco Unified Border Element by using RFC2833 as the preferred relay mechanism and KPML as the next preferred relay mechanism. The engineer logs in to the CUBE and enters the dial-peer configuration level.

  Which command should be run at the dial-peer configuration level?

  A. dtmf-relay sip-kpml rtp-nte
  B. dtmf-relay rtp-inband sip-kpml
  C. dtmf-relay sip-kpml rtp-inband
  D. dtmf-relay rtp-nte sip-kpml
  D. dtmf-relay rtp-nte sip-kpml