Cisco 350-020 Online Practice Questions and Exam Preparation

Cisco 350-020 Online Questions & Answers

• Question 311:

  Click the Exhibit button to view the configuration.

  

  Look at the router configuration above. If this router has a configuration-register setting of 0x102, select the proper boot sequence:

  A. The router will try to use the image "rsp-isv-mz. 112-8.P" on slot 0, then attempt to boot from a network server, and finally boot fromROM.
  B. The router will try use the image "rsp-isv-mz. 112-8.P" on slot 0, then attempt to boot from any other valid image in flash, and finally boot fromROM.
  C. The router will try to use the image "rsp-isv-mz.112-8.P" on slot0, and then it will boot fromROM.
  D. The router will try to use the image "rsp-isv-mz. 112-8.P" on slot 0, and then attempt to boot from a network server.
  A. The router will try to use the image "rsp-isv-mz. 112-8.P" on slot 0, then attempt to boot from a network server, and finally boot fromROM.

• Question 312:

  On each LAN segment with multiple bridges running spanning tree, the bridge closest to the:

  A. Designated bridge is selected as root bridge
  B. Root bridge is selected as designated bridge
  C. Root bridge is not selected as designated bridge
  D. Designated bridge is not selected as root bridge
  B. Root bridge is selected as designated bridge

• Question 313:

  What is an active filter?

  A. Prisms
  B. Dielectric thin film interface filter
  C. Diffraction grating
  D. Semi-conductor filter
  E. Bragg Grating
  D. Semi-conductor filter

• Question 314:

  Click the Exhibit button to view the routing table.

  

  If a router had the three routes listed, which one of the routes would forward a packet destined for 10.1.1.1?

  A. 10.1.0.0/16 through EIGRP, because EIGRP routes are always preferred over OSPF or static routes.
  B. 10.1.0.0/16 static, because static routes are always preferred over OSPF or EIGRP routes.
  C. 10.1.1.0/24 through OSPF because the route with the longest prefix is always chosen.
  D. Whichever route appears in the routing table first.
  E. The router will load share between the 10.1.0.0/16 route through EIGRP and the 10.1.0.0/16 static route.
  C. 10.1.1.0/24 through OSPF because the route with the longest prefix is always chosen.

• Question 315:

  What is the difference in power at the input and the output of the device under test?

  A. Cross Talk
  B. Return Loss
  C. Insertion Loss
  D. Passband
  E. None of the above
  C. Insertion Loss

• Question 316:

  Which three events might you diagnose as the cause of a line switching event?

  A. Loss of signal and frame
  B. Line AIS (all ones in STS pointer)
  C. Routine exercises
  D. Excessive signaling messages
  E. Excessive bit errors in overhead
  F. Switched photon elements
  A. Loss of signal and frame
  B. Line AIS (all ones in STS pointer)
  E. Excessive bit errors in overhead

• Question 317:

  RPR capability on the ML-series cards increases the scalability of the ML architecture from 10 cards per ring to how many cards per ring?

  A. 16
  B. 32
  C. 255
  D. 4080
  B. 32

• Question 318:

  With CGMP enabled, which are unique about the following MAC address range: 01-00-5E-00-00- 00 to 01-00-5E-00-00-FF? (multiple answer)

  A. CGMP does not prune those MAC addresses.
  B. They contain the CGMP Multicast addresses for the IGMP Leaves and IGMP Queries.
  C. CGMP filters those MAC addresses when they arrive at the processor
  D. They are the reserved IP addresses of 224.0.0.0 to 224.0.0.255 for forwarding local IP multicast traffic in a single Layer 3 hop.
  A. CGMP does not prune those MAC addresses.
  B. They contain the CGMP Multicast addresses for the IGMP Leaves and IGMP Queries.
  D. They are the reserved IP addresses of 224.0.0.0 to 224.0.0.255 for forwarding local IP multicast traffic in a single Layer 3 hop.

• Question 319:

  What do directly modulated transponders vary to the laser in order to transmit an optical signal?

  A. Voltage
  B. Resistance
  C. Current
  D. Output signal
  E. Temperature
  C. Current

• Question 320:

  ML-series QoS handling of multicast and broadcast traffic involves:

  A. Putting all multicast and broadcast traffic in its own queue and giving it priority over other traffic.
  B. Putting multicast and broadcast traffic in its own queue and allocating a 10% port bandwidth guarantee.
  C. Configuration using the "bandwidth" command allowing QoS guarantees for multicast and broadcast traffic.
  D. All multicast and broadcast being treated as best effort (BE) traffic.
  B. Putting multicast and broadcast traffic in its own queue and allocating a 10% port bandwidth guarantee.