Cisco 300-415 Online Practice Questions and Exam Preparation

Cisco 300-415 Online Questions & Answers

• Question 101:

  An engineer must use data prefixes to configure centralized data policies using the vManage policy configuration wizard. What is the first step to accomplish this task?

  A. Configure network topology.
  B. Apply policies to sites and VPNs.
  C. Configure traffic rules.
  D. Create groups of interest.
  D. Create groups of interest.

  ---

  https://www.cisco.com/c/en/us/td/docs/routers/sdwan/configuration/policies/vedge/policies-book/data-policies.html#id_107211

• Question 102:

  Which two types of SGT propagation are supported by Cisco TrustSec? (Choose two.)

  A. key chain
  B. offline tagging
  C. SXP
  D. reconciliation
  E. inline tagging
  C. SXP
  E. inline tagging

  ---

• Question 103:

  Which data policy configuration influences BGP routing traffic flow from LAN to WAN?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  D. Option D

  ---

• Question 104:

  A network administrator is configuring a centralized control policy based on match action pairs for multiple conditions. Which order must be configured to prefer Prefix List over TLOC and TLOC over Origin?

  A. highest to lowest sequence number
  B. nonsequential order
  C. deterministic order
  D. lowest to highest sequence number
  D. lowest to highest sequence number

  ---

  By assigning higher sequence numbers to the rules or match action pairs you want to prioritize, you ensure that these rules are evaluated first. In this case, you would configure the Prefix List rule with a higher sequence number than the TLOC rule, and the TLOC rule with a higher sequence number than the Origin rule.

• Question 105:

  DRAG DROP

  Drag and drop the BFD parameters from the left onto the BFD configurations on the right.

  Select and Place:

  

  

  ---

  https://sdwandocs.cisco.com/Product_Documentation/vManage_Help/Release_18.2/Configuration/Templates/BFD

• Question 106:

  Which component is used to optimize the multicast distribution tree enabled through the multicast network?

  A. IGMP client
  B. vManage controllers
  C. VPN concentrator
  D. OMP replicator
  D. OMP replicator

• Question 107:

  What are the default username and password for vSmart Controller when it is installed on a VMware ESXi hypervisor?

  A. username admin password admin
  B. username admin password cisco
  C. username cisco password admin
  D. username cisco password cisco
  A. username admin password admin

  ---

  The default username and password for a vSmart Controller when it is installed on a VMware ESXi hypervisor typically follow the same default credentials used in the Cisco SD-WAN environment. These default credentials are provided during the initial setup or installation of the vSmart Controller, and they are typically as follows: Default Username: admin Default Password: admin

• Question 108:

  Which feature builds transport redundancy by using the cross link between two redundant WAN Edge routers?

  A. OMP
  B. zero-touch provisioning
  C. quality of service
  D. TLOC extension
  D. TLOC extension

• Question 109:

  Refer to the exhibit.

  

  Customer XYZ cannot provison dual connectivity on both Its routers due to budget constratnts but wants to use tnth RI and R2 interface for users behind them for load toward the hub site. Which configurauon achieves this objectives?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  A. Option A

• Question 110:

  Refer to the exhibit.

  vEdge-2(config-vpn-0)#interface ge0/2.101vEdge-2(config-interface)#ip address 10.1.100.0/24vEdge-2(config-interface)#tloc-extension ge0/0vEdge-2(config-interface)#mtu 1496vEdge-2(config-interface)#no shutdown

  

  What binding is created using the tloc-extension command?

  A. between ge0/2.101 of port-type transport and ge0/0 of port-type service
  B. between ge0/2.101 of port-type service and ge0/0 of port-type service
  C. between ge0/2.101 of port-type service and ge0/0 of port-type transport
  D. between ge0/2.101 of port-type transport and ge0/0 of port-type transport
  D. between ge0/2.101 of port-type transport and ge0/0 of port-type transport

  ---