Exam Deatils

  • Exam Code
    :300-135
  • Exam Name
    :Troubleshooting and Maintaining Cisco IP Networks (TSHOOT v2.0)
  • Certification
    :CCNP Routing and Switching
  • Vendor
    :Cisco
  • Total Questions
    :346 Q&As
  • Last Updated
    :Apr 15, 2019

Cisco CCNP Routing and Switching 300-135 Questions & Answers

  • Question 1:

    A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

    A. RouterA received a hello packet with mismatched autonomous system numbers.

    B. RouterA received a hello packet with mismatched hello timers.

    C. RouterA received a hello packet with mismatched authentication parameters.

    D. RouterA received a hello packet with mismatched metric-calculation mechanisms.

    E. RouterA will form an adjacency with RouterB.

    F. RouterA will not form an adjacency with RouterB.

  • Question 2:

    You must add encryption to a GRE tunnel. Which IPsec configuration is recommended for a VPN with NAT transversal?

    A. Enable SHA on the tunnel

    B. Implement IPsec transport mode

    C. Enable MD5 on the tunnel

    D. Implement IPsec tunnel mode

  • Question 3:

    Client is unable to ping IP 209.65.200.241

    Solution

    Steps need to follow as below:

    When we check on client 1 and Client 2 desktop we are not receiving DHCP address from R4 Ipconfig ----- Client will be getting 169.X.X.X

    On ASW1 port Fa1/0/ 1 and Fa1/0/2 access port VLAN 10 was assigned which is using IP address 10.2.1.0/24 Sh run ------- and check for running config of int fa1/0/1 and fa1/0/2 ====================================================

    ====================================================

    Here we are not able to see access Vlan10 configured for Port Fa1/0/1 and Fa1/0/2

    Change required: On ASW1, for configuring Access Vlan under interface fa1/0/1 and 1/0/2 we have to enable command switchport access vlan 10

    The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241.

    After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the

    209.65.200.241 address.

    Use the supported commands to isolated the cause of this fault and answer the following questions.

    What is the solution to the fault condition?

    A. R1

    B. R2

    C. R3

    D. R4

    E. DSW1

    F. DSW2

    G. ASW1

    H. ASW2

  • Question 4:

    ===============================================================================

    Client is unable to ping IP 209.65.200.241

    Solution

    Steps need to follow as below:

    When we check on client 1 and Client 2 desktop we are not receiving DHCP address from R4 Ipconfig ----- Client will be receiving IP address 10.2.1.3

    IP 10.2.1.3 will be able to ping from R4 , R3, R2 but not from R1

    Check for neighborship of ospf sh ip ospf nei ----- Only one neighborship is forming with R2 and i.e. with R3 Since R2 is connected to R1 and R3 with routing protocol ospf than there should be 2 neighbors seen but only one is seen

    Need to check running config of R2 and R3 for interface Sh run -------------------------- Interface Serial0/0/0/0.12 on R2

    Sh run -------------------------- Interface Serial0/0/0/0 on R1

    Change required: On R1, for IPV4 authentication of OSPF command is missing and required to configure------ ip ospf authentication message-digest The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the

    209.65.200.241 address.

    Use the supported commands to isolated the cause of this fault and answer the following questions.

    The fault condition is related to which technology?

    A. BGP

    B. NTP

    C. IP NAT

    D. IPv4 OSPF Routing

    E. IPv4 OSPF Redistribution

    F. IPv6 OSPF Routing

    G. IPv4 layer 3 security

  • Question 5:

    Which of the following would be considered reasonable network maintenance tasks? (Choose all that apply.)

    A. Ensuring compliance with legal regulations and corporate policies

    B. Troubleshooting problem reports

    C. Planning for network expansion

    D. Providing support to sales and marketing

    E. Giving presentations to management

    F. Monitoring and tuning network performance

  • Question 6:

    Which keywords can be used with debug condition to filter output? (Choose two.)

    A. Port Number

    B. Interface ID

    C. Protocol

    D. User Name

    E. Packet Size

  • Question 7:

    Connectivity from R3 to R4, R5 and R6 has been lost. How should connectivity be reestablished?

    A. Configure R4 with a virtual link to 192.168.13.2

    B. Change the R3 and R4 hello-interval and retransmit-interface timers to zero so the link won't go down.

    C. Add an OSPF network statement for 4.4.4.4 0.0.0.0 area 1 in R3

    D. Add an OSPF network statement for 192.168.34.3 0.0.0.255 area 2 in R3

    E. Add an OSPF network statement for 192.168.34.0 0.0.0.255 area 1 in R3

  • Question 8:

    A question about which login procedure will ask first. You see a running config user logins. aaa new-model aaa authentication login default tacacs+ enable aaa authentication login ONLYLOCAL local aaa authentcation ppp default radius local username Cisco password Cisco123 line vty 0 4

    A. local

    B. line

    C. RADIUS

    D. TACACS+

  • Question 9:

    Scenario:

    A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality.

    The OSPF neighbour relationship has been lost between R1 and R3.

    What is causing this problem?

    A. The serial interface in R1 should be taken out of the shutdown state.

    B. A neighbor statement needs to be configured in R1 and R3 pointing at each other.

    C. The R1 network type should be changed to point-to-multipoint non-broadcast.

    D. The hello, dead and wait timers on R1 need to be reconfigured to match the values on R3.

  • Question 10:

    About AAA:

    username nmops privilege 15 secret Cisco 123

    username nmeng privillege 15 secret 123Cisco

    enable secret Str0ng34156732

    aaa authentication login default group tacacs+ local aaa authentication enable default group tacacs+

    aaa authorization config-commands

    aaa authourization exec default group tacacs+ if-authenticated aaa accounting exec default start-stop group tacacs+ aaa accounting commands 5 default stop-only group tacacs+ aaa accounting commands 15 default start-stop group tacacs+

    aaa accounting system default start-stop group tacacs+ You are performing a peer review on this implementation script, which is intended to enable AAA on a device. if the script is deployed which two effects does it have on the device?

    (choose two)

    A. part of the script is rejected

    B. the device authenticates users against the local database first

    C. the device fails to perform AAA because session-id common command is missing

    D. the device authenticates all users except nmops and nmeng against the TACAS+ database

    E. the device fails to perform AAA because the aaa new-model command is missing

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 300-135 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.