Cisco 300-115 Online Practice Questions and Exam Preparation

Cisco 300-115 Online Questions & Answers

• Question 341:

  Behavior of an access port when a tagged packet is received other than the access VLAN value.

  A. Tag is removed and packet is forwarded of the VLAN mentioned in the tag.
  B. tag is removed and packet is forwarded on the VLAN of the access port
  C. https://www.CertBus.com/300-115.html
  D. packet is dropped
  D. packet is dropped

• Question 342:

  Refer to the exhibit.

  

  Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?

  A. Switch B is configured in transparent mode.
  B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.
  C. The VTP revision number of the Switch B is higher than that of Switch A.
  D. The trunk between Switch A and Switch B is misconfigured.
  A. Switch B is configured in transparent mode.

  ---

  VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements, but transparent switches do

  forward VTP advertisements that they receive out their trunk ports in VTP Version 2.

  Reference:

  http://www.cisco.com/en/US/tech/tk389/tk689/technologies_tech_note09186a0080094c52.shtml

• Question 343:

  Drag and Drop

  Select and Place:

  

  

• Question 344:

  Drag and Drop

  Select and Place:

  

  

• Question 345:

  Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.

  

  What issue is causing Router R1 and R2 to both be displayed as the HSRP active router for group 2?

  A. The HSRP group number mismatch
  B. The HSRP group authentication is misconfigured
  C. The HSRP Hello packets are blocked
  D. The HSRP timers mismatch
  E. The HSRP group priorities are different
  B. The HSRP group authentication is misconfigured

  ---

  Based on the configuration output, we see that authentication is configured on R2, but not on R1:

  

  

  This can be further verified by issuing the "show standby" command on each router.

  

• Question 346:

  Which two command sequences must you enter on a pair of switches so that they negotiate an EtherChannel using the Cisco proprietary port-aggregation protocol? (Choose two.)

  A. channel-protocol lacp channel-group 1 mode on
  B. channel-protocol pagp channel-group 1 mode auto
  C. channel-protocol lacp channel-group 1 mode active
  D. channel-protocol pagp channel-group 1 mode desirable
  E. channel-protocol pagp channel-group 1 mode on
  B. channel-protocol pagp channel-group 1 mode auto
  D. channel-protocol pagp channel-group 1 mode desirable

• Question 347:

  Which two types of protocols use VLAN 1 as the default? (Choose two.)

  A. CDP
  B. STP
  C. VTP
  D. https://www.certbus.com/300-115.html
  A. CDP
  C. VTP

• Question 348:

  Drag and Drop

  Select and Place:

  

  

• Question 349:

  Which two commands to command sequences configure a switch so that it tags native VLAN 3939? (Choose two.)

  A. interface GigabitEthernet0/0 description to HR Building M 9373-810 witchport trunk native vlan 3939
  B. switch(config)#set switch native vlan 3939
  C. switch (config)#vlan dot1q native vlan 3939
  D. Interface GigabitEthernet0/0 Description to HR Building M 9373-810 Encapsulation dot1q tag vlan native 3939
  E. switch(config)#vlan dotlq tag native
  A. interface GigabitEthernet0/0 description to HR Building M 9373-810 witchport trunk native vlan 3939
  E. switch(config)#vlan dotlq tag native

• Question 350:

  Drag and Drop

  Drag and drop the statements about remote security databases from the left onto the correct security database types on the right.

  Select and Place: