Cisco 300-115 Online Practice Questions and Exam Preparation

Cisco 300-115 Online Questions & Answers

• Question 201:

  which two statements about HSRP timers are true? (Choose two.)

  A. the default Hold timer is 15 seconds.
  B. the default Hello timer is 3 seconds.
  C. the default Hello timer is 5 seconds.
  D. the default Hold timer is 10 seconds.
  E. the default Hello timer is 30 seconds.
  F. the default Hold timer is 30 seconds.
  B. the default Hello timer is 3 seconds.
  D. the default Hold timer is 10 seconds.

• Question 202:

  After you connected a host to switch port G0/1, the port error disabled. Which command can you enter to determine the reason?

  A. show interfaces g0/1 status
  B. show run interface g0/1
  C. show ip int brief
  D. show log
  D. show log

• Question 203:

  Which statement about the connection of two switches with several links using LACP link aggregation on IOS is true?

  A. By default, when an LACP channel is configured, the LACP channel mode is off.
  B. By default, when an LACP channel is configured, the LACP channel mode is on
  C. By default, when an LACP channel is configured, the LACP channel mode is active.
  D. By default, when an LACP channel is configured, the LACP channel mode is passive.
  D. By default, when an LACP channel is configured, the LACP channel mode is passive.

• Question 204:

  Which VTP mode is needed to configure an extended VLAN, when a switch is configured to use VTP versions 1 or 2?

  A. transparent
  B. client
  C. server
  D. Extended VLANs are only supported in version 3 and not in versions 1 or 2.
  A. transparent

• Question 205:

  Refer to the exhibit.

  

  You have applied these configuration to SwitchA,B,C, and D respectively, and the switches are connected to one another on a trunk port that is passing all VLAN traffic. Which statement about traffic on the network is true?

  A. Unless a Layer 3 device is installed, host on any of the switches will be able to communicate only with other hosts on the same switch.
  B. Host on all four switches can communicate normally with one another over the trunk port.
  C. Host on all four switches can communicate normally with one another on VLAN 10 only.
  D. Unless a Layer 3 device is installed, host on the FastEthernet 0/1 interfae of switch D will be unable to communicate with hosts on the other switches
  D. Unless a Layer 3 device is installed, host on the FastEthernet 0/1 interfae of switch D will be unable to communicate with hosts on the other switches

• Question 206:

  What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up?

  A. 1
  B. 5
  C. 10
  D. 15
  C. 10

  ---

  The standby track interface configuration command ties the router hot standby priority to the availability of its interfaces and is useful for tracking interfaces that are not configured for HSRP. When a tracked interface fails, the hot standby priority on the device on which tracking has been configured decreases by

  10. If an interface is not tracked, its state changes do not affect the hot standby priority of the configured device. For each interface configured for hot standby, you can configure a separate list of interfaces to be tracked. Reference: http:// www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/ release/12.1_19_ea1/ confi guration/guide/swhsrp.html

• Question 207:

  Which three authentication types does VRRP support ?(Choose three)

  A. Plain-text
  B. CHAP
  C. PAP
  D. 802.1X
  E. MD5
  F. No Authentication
  A. Plain-text
  E. MD5
  F. No Authentication

• Question 208:

  Which type of port can serve as a Cisco StackWise Virtual link?

  A. an uplink port only
  B. any physical port
  C. a downlink port only
  D. a switched port only
  B. any physical port

• Question 209:

  Which command apply to verify errdisable on any interface?

  A. show err-disable detect
  B. show interfaces err-disable status
  C. http://certbus.com
  D. http://certbus.com
  B. show interfaces err-disable status

• Question 210:

  Which Cisco StackWise feature is supported?

  A. using different versions of the Cisco IOS on each switch
  B. using different SDM templates on each switch
  C. using same software feature set on all members
  D. using mixed software feature set on all members
  C. using same software feature set on all members