CompTIA 220-1001 Online Practice Questions and Exam Preparation

CompTIA 220-1001 Online Questions & Answers

• Question 531:

  An end user reports being unable to connect to the Internet. A technician tries to ping a well-known site and gets no response. When running ipconfig, the technician notices the IP address of the workstation is 169.254.255.254 with a subnet mask of 255.255.0.0. Which of the following is MOST likely causing the problem?

  A. The proxy server is configured incorrectly.
  B. The subnet mask needs to be changed.
  C. The DHCP server pool is exhausted.
  D. The DNS cache needs to be flushed.
  C. The DHCP server pool is exhausted.

• Question 532:

  Which of the following is the standard number of pins on an ATX connector that connects from the PSU to the motherboard?

  A. 8
  B. 16
  C. 24
  D. 32
  C. 24

• Question 533:

  A user is presenting from a tablet at a conference and has had it plugged in the entire time, but the battery level is at 15% capacity The user forgot the tablet's power adapter at home and borrowed an adapter for a similar but smaller tablet from a coworker Which of the following is the MOST likely cause of the issue?

  A. The tablet overheated, and the user should stop using it
  B. The tablet was connected to the projector via the wrong video adapter
  C. The tablet was not charging due to incorrect power
  D. The tablet's battery is swollen and needs to be replaced
  C. The tablet was not charging due to incorrect power

• Question 534:

  A technician needs to secure and optimize traffic on a local network by separating client workstations from web servers. The technician only has administrative permissions on the Layer 2 switch to which all of the devices are connected. Which of the following should the technician complete to accomplish this goal?

  A. Create a separate DHCP scope for the web servers.
  B. Implement an ACL on the switch.
  C. Place the web servers in a DMZ.
  D. Configure the web servers in a separate VLAN.
  E. Set up the web servers on a different domain.
  D. Configure the web servers in a separate VLAN.

• Question 535:

  A technician needs to implement a test server with RAID using tour hard drives. The only requirement is the server must have the maximum amount of storage possible. Which of the following RAID levers should a technician configure on the server to meet the requirement?

  B. 1
  C. 5
  D. 10
  C. 5

• Question 536:

  A technician wants to build a computer with the largest possible motherboard size for maximum expandability Which of the following form factors would BEST enable this requirement?

  A. mlTX
  B. ATX
  C. ITX
  D. mATX
  B. ATX

• Question 537:

  An end user brings in a laptop that no longer charges. A technician troubleshoots the laptop and notices it works while the power adaptor is plugged in but shuts down as soon as it is unplugged.

  Which of the following is the NEXT best step to resolve this issue?

  A. Plug the laptop into another power outlet.
  B. Replace the power adaptor.
  C. Replace the laptop's battery.
  D. Plug the laptop into a UPS.
  C. Replace the laptop's battery.

• Question 538:

  A customer is purchasing a gaming laptop and wants the maximum number of IOPS. Which of the following hard drives should be installed in the laptop?

  A. Hybrid SSD
  B. SATA SSD
  C. NVMe SSD
  D. IDE SSD
  B. SATA SSD

• Question 539:

  A technician is setting up a WiFi-enabled thermostat for a customer, but the customer is concerned about IoT devices getting hacked. Which of the following BEST address the customer's concerns? (Choose two.)

  A. Use the latest encryption standard on the wireless network and set a strong password.
  B. Enable two-factor authentication for the IoT device's cloud account, if it is available.
  C. Separate the IoT thermostat by segregating it in a DMZ network.
  D. Disable wireless access on the thermostat to make it unshakable.
  E. Upgrade the customer's router to the latest version to improve network security.
  F. Upgrade the customer's wireless network encryption to WPA.
  A. Use the latest encryption standard on the wireless network and set a strong password.
  B. Enable two-factor authentication for the IoT device's cloud account, if it is available.

• Question 540:

  SIMULATION

  You need to configure your mobile device to send and receive electronic messages from your company.

  You must use the company's WLAN as all e-mail services are on default non-secure ports.

  The company's WLAN is broadcasting across the company for easier access. Both incoming and outgoing servers require login credentials.

  Use the following parameters:

  1.

  Email address tech@techies com

  2.

  Password P@SSwOrd

  3.

  Pop techies com Port 110 Security. None

  4.

  IMAP techies com Port 993 Security SSL

  5.

  smtp.techies.com Port 465 Security: TLS

  6.

  Company SSID Techies

  7.

  Security WPA2

  8.

  Passphrase P@SSwOrd

  9.

  SSID is not broadcasted

  Instructions: You are not authorized to use the Company's WLAN The outgoing server does not require login credentials. When you have completed the simulation, please select the done button to submit your answer.

  Configure Mobile Device

  Instruction: Configure the settings to send and receive electronic messages from the company.

  Update the mobile device's parameters to fit the criteria.

  If at any time you would like to bring back the initial state of the simulation, please click the Reset All button.

  

  

  A. Check the answer in explanation.
  A. Check the answer in explanation.

  ---

  Since we are instructed to not use the company's WLAN we only need to worry about the email settings and ignore the WiFi and Networks tab. On the MAIL tab enter information as shown below:

  

  That should be all that is needed.

  Tips: The mobile has save button in top right corner, your instructions might cover it so watch out for that, first is IMAP then SMTP.