VCE 210-010 Online Practice Questions and Exam Preparation

VCE 210-010 Online Questions & Answers

• Question 91:

  When powering on a Vblock System what is the correct power up sequence?

  A. Switches, AMP, SAN, UCS chassis, and UCS blades
  B. Switches, SAN, UCS chassis, UCS blades, and AMP
  C. Switches, AMP, UCS chassis, UCS blades, and SAN
  D. Switches, SAN, AMP, UCS chassis, and UCS blades
  A. Switches, AMP, SAN, UCS chassis, and UCS blades

• Question 92:

  What are three core VMware components of a Vblock System? (Choose three.)

  A. vCenter server
  B. Update Manager
  C. ESRS
  D. ESX
  E. ESXi
  A. vCenter server
  B. Update Manager
  E. ESXi

• Question 93:

  EMC Ionix UIM/P services are managed through service profiles comprised of server, network, and storage profiles. Before managing a service offering, which two actions must be completed? (Choose two.)

  A. Discover the Vblock System.
  B. Install ESXi onto blades for discovery preparation.
  C. Mark graded storage pool as available.
  D. Configure the auto deploy server with IP pool.
  A. Discover the Vblock System.
  C. Mark graded storage pool as available.

• Question 94:

  Customers provide the information used to develop the Logical Configuration Survey (LCS) before manufacturing begins.

  What information is required? (Choose two.)

  A. syslog server IP address
  B. NTP server IP address
  C. method of device access (telnet or SSH)
  D. MIB browser IP address
  B. NTP server IP address
  C. method of device access (telnet or SSH)

• Question 95:

  A SAN administrator must use the zone commit command to activate a zone set on a Cisco MDS 9148. Which feature is enabled on the switch?

  A. hardware zoning by access control lists
  B. enhanced zoning
  C. extended broadcast zoning
  D. basic zoning
  B. enhanced zoning

• Question 96:

  What are two expected results of the VMware vMotion test plan conducted by VCE at the completion of a Vblock System build? (Choose two.)

  A. No unexpected errors or faults occur.
  B. The secondary VSM takes over from the primary VSM.
  C. There will be minimal packet loss during vMotion.
  D. Traffic fails over to the redundant port channel each time a port-channel is disabled.
  A. No unexpected errors or faults occur.
  C. There will be minimal packet loss during vMotion.

• Question 97:

  You are required to setup the network interface on a Vblock System 320 storage array, which is used for file level access. In which mode should the interface be configured?

  A. fail safe networking
  B. link aggregation
  C. Ethernet channel
  D. network trunking
  B. link aggregation

• Question 98:

  Which network capability does the Cisco Nexus 1000V provide in a Vblock System 720?

  A. vNic drivers
  B. IP address assignment
  C. distributed switching
  D. routing
  C. distributed switching

• Question 99:

  VCE Vision Intelligent Operations has been installed on a customer's Vblock System.

  Which two parameters would be selected within the configureSNMP command? (Choose two.)

  A. delete trap target
  B. sysContact
  C. add v1/v2c trap target
  D. sysLocation
  A. delete trap target
  C. add v1/v2c trap target

• Question 100:

  In a Vblock System 320, which type of port channel is configured from the Cisco Nexus 5548 switch to the fabric interconnects?

  A. static port channel
  B. virtual port channel (vPC)
  C. enhanced virtual port channel
  D. virtual port channel plus (vPC+)
  B. virtual port channel (vPC)