Cisco 200-125 Online Practice Questions and Exam Preparation

Cisco 200-125 Online Questions & Answers

• Question 831:

  Which dynamic routing protocol uses only the hop count to determine the best path to a destination?

  A. IGRP
  B. RIP
  C. EIGRP
  D. OSPF
  C. EIGRP

• Question 832:

  Which IPv6 routing protocol uses multicast group FF02::9 to send updates?

  A. static
  B. RIPng
  C. OSPFv3
  D. IS-IS for IPv6
  B. RIPng

• Question 833:

  Which protocol is typically used for communication between an NMS and an agent on a network device?

  A. syslog
  B. MIB
  C. SNMP
  D. SMTP
  C. SNMP

• Question 834:

  During which phase of PPPoE is PPP authentication performed?

  A. the PPP Session phase
  B. Phase 2
  C. the Active Discovery phase
  D. the Authentication phase
  E. Phase 1
  A. the PPP Session phase

• Question 835:

  Drag the security features on the left to the specific security risks they help protect against on the right. (Not all options are used.)

  Select and Place:

  

  

• Question 836:

  Which two pieces of information can be shared with LLDP TLVs? (Choose two)

  A. device management address.
  B. device type
  C. spanning-tree topology
  D. routing configuration
  E. access-list configuration
  A. device management address.
  B. device type

  ---

  Explanation: TLV advertises a single type of information such as its device ID, type or management addresses.

• Question 837:

  Scenario:

  You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

  Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

  NAT is enabled on router R1.

  The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

  R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

  You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

  

  

  

  

  Examine the DHCP configuration between R2 and R3; R2 is configured as the DHCP server and R3 as the client. What is the reason R3 is not receiving the IP address via DHCP?

  A. On R2. The network statement In the DHCP pool configuration is incorrectly configured.
  B. On R3. DHCP is not enabled on the interface that is connected to R2.
  C. On R2, the interface that is connected to R3 is in shutdown condition.
  D. On R3, the interface that is connected to R2 is in shutdown condition.
  B. On R3. DHCP is not enabled on the interface that is connected to R2.

  ---

  Please check the below:

  

• Question 838:

  Scenario:

  You work for a company that provides managed network services, and of your real estate clients running a small office is experiencing network issues, Troubleshoot the network issues.

  Router R1 connects the main office to internet, and routers R2 and R3 are internal routers

  NAT is enabled on Router R1.

  The routing protocol that is enable between routers R1, R2, and R3 is RIPv2.

  R1 sends default route into RIPv2 for internal routers to forward internet traffic to R1.

  Server1 and Server2 are placed in VLAN 100 and 200 respectively, and dare still running router on stick configuration with router R2.

  You have console access on R1, R2, R3, and L2SW1 devices. Use only show commands to troubleshoot the issues.

  

  

  

  

  

  

  

  

  

  

  

  

  Users in the main office complain that they are unable to reach internet sites.

  You observe that internet traffic that is destined towards ISP router is not forwarded correctly on Router R1. What could be an issue?

  Ping to Internet server shows the following results from R1:

  R1#ping 209.165.200.225

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 209.165.200.225. timeout is 2 seconds:

  .....

  Success rate is 0 percent (0/5)

  A. The next hop router address for the default route is incorrectly configured.
  B. Default route pointing to ISP router is configured with AD of 255.
  C. Default route pointing to ISP router is not configured on Router R1
  D. Router R1 configured as DHCP client is not receiving default route via DHCP from ISP router.
  C. Default route pointing to ISP router is not configured on Router R1

  ---

  (Default Static Route will fix the problem to connect to ISP router)

  

• Question 839:

  which port security violation mode drops traffic from unknown MAC addresses and sends an SNMP trap?

  A. restrict
  B. shutdown VLAN
  C. protect
  D. shutdown
  A. restrict

• Question 840:

  interface fa0/0 ip address x.x.x.33 255.255.255.224 router bgp XXX neighbor x.x.x.x remote as x.x.x.x

  You need to advertise the network of Int fa0/0.

  A. x.x.x.32 mask 255.255.255.224
  B. x.x.x.32 255.255.255.224
  C. x.x.x.32 mask 0.0.0.31
  D. x.x.x.33 mask 255.255.255.224
  A. x.x.x.32 mask 255.255.255.224