Oracle 1Z0-822 Online Practice Questions and Exam Preparation

Oracle 1Z0-822 Online Questions & Answers

• Question 131:

  Examine the following command:

  ipadm create-addr -T static -a 192.168.1.112/26 net0/v6

  Which two statements are true?

  A. The interface is plumbed.
  B. The interface is marked down.
  C. The netmask value is ffffffc0.
  D. The link local IPv6 address fe80::112 is created.
  E. Multicast datagrams are not enabled on this interface.
  C. The netmask value is ffffffc0.
  D. The link local IPv6 address fe80::112 is created.

• Question 132:

  You added an interface to the IPMP group ipmp0 with the following commands:

  # ipadm create-ip net4 # ipadm add-ipmp i net4 ipmp0 Which statement regarding the newly added interface is correct?

  A. Link state failure detection will not occur.
  B. Probe-based failure detection will not occur.
  C. Without a data IP address, it cannot become active.
  D. These changes will be lost when the system is booted.
  A. Link state failure detection will not occur.
  C. Without a data IP address, it cannot become active.

• Question 133:

  Consider the following command and output:

  user$ newtask v p canada Identify the output.

  A. the task ID for the project canada
  B. the project ID for the project canada
  C. the task ID for the shell
  D. the task ID for all jobs already running in the shell
  C. the task ID for the shell

• Question 134:

  You have set resource controls on a project. Now you want to set up syslog to monitor a particular resource control and log a message whenever the resource control is exceeded. Which option would you choose to activate logging on the global resource control facility to establish a syslog action on a resource control?

  A. Use the rctladm command to enable the global syslog attribute of a resource control.
  B. Use the prctl command to enable the global syslog attribute of resource control.
  C. Use the ipcs command to enable the global syslog attribute of a resource control.
  D. Use the setrctl command to enable the global syslog attribute of a resource control.
  E. By default, global logging of resource control violations is already enabled. Make an entry in the syslog.conf file and refresh the system-log service.
  A. Use the rctladm command to enable the global syslog attribute of a resource control.

• Question 135:

  Which three statements describe Solaris 11 boot environments (BEs)?

  A. A full backup of your OS image is provided.
  B. Packages can be installed and uninstalled in an inactive BE.
  C. The OS can be upgraded in an active BF while the system is live without impacting production.
  D. A new BE can be created from the snapshot of an existing BE.
  E. A BE can become active without rebooting the system.
  F. An active BE can be unmounted and upgraded without impacting production.
  C. The OS can be upgraded in an active BF while the system is live without impacting production.
  D. A new BE can be created from the snapshot of an existing BE.
  F. An active BE can be unmounted and upgraded without impacting production.

• Question 136:

  What are targets for IPMP probe-based failure detection configured by?

  A. responses to SNMP requests
  B. specifying host routes in the routing table
  C. specifying hosts in /etc/default/mpathd
  D. setting the property svc:/network/ipmp/config/transitive-probing
  B. specifying host routes in the routing table

• Question 137:

  You are considering using IPMP and Link Aggregation. Which two statements are true about these technologies?

  A. IPMP requires all interfaces to support the same bit rate.
  B. Both technologies can increase outbound bandwidth.
  C. Link Aggregation does not offer link failure protection.
  D. Link Aggregation requires all interfaces to support the same bit rate.
  E. IPMP supports load spreading across all interfaces for inbound traffic
  C. Link Aggregation does not offer link failure protection.
  E. IPMP supports load spreading across all interfaces for inbound traffic

• Question 138:

  The zpool configuration on serverA is:

  pool 1 c3t2d0 c3t3d0 pool 2 c3t4d0 c3t5d0

  The zpool configuration on servetB is:

  pool1 mirror-0 c3t2d0 c3t3d0 mirror-1 c3t4d0 c3t5d0

  Which option will modify the configuration on serverA to match serverB?

  A. zpool destroy pool2 zpool attach pool1 c3t4d0 c3t5d0
  B. zpool destroy pool2 zpool attach pool1 c3t2d0 c3t2d0 c3t4d0 c3t5d0
  C. zpool destroy pool2 zpool add pool1 c3t4d0 c3t5d0
  D. zpool destroy pool2 zpool mirror pool1 pool2
  E. zpool destroy pool2 zpool attach pool1 c3t2d0 attach pool1 c3t3d0 zpool attach pool1 c3t4d0 attach pool1 c3t5d0
  F. zpool destroy pool1; zpool destroy pool2; zpool create pool1 mirror c 3t2d0 c3t3d0 mirror c4t4d0 c3t5d0
  F. zpool destroy pool1; zpool destroy pool2; zpool create pool1 mirror c 3t2d0 c3t3d0 mirror c4t4d0 c3t5d0

• Question 139:

  Frank is a member of two projects on you system. He has a process running in a project called project- clock and needs to move it under the other project he belongs to. Which command must Frank use to move the process?

  A. setproject
  B. newtask
  C. projmod
  D. prtcl
  C. projmod

• Question 140:

  You are the administrator of on Oracle Solaris 11 Al server. You added a client. Then you created a custom manifest, custom criteria, and a custom profile for the client. You made an error in the package path within the custom manifest. When will the error appear?

  A. when the manifest is checked during client preinstall
  B. when the manifest is used during client install
  C. when the manifest is updated on the AI server
  D. when the manifest is added to the AI server
  D. when the manifest is added to the AI server