A network engineer wants to optimize a published load balanced SSL virtual server for WAN connection with long delay, high bandwidth with minimal packet drops.
What would the network engineer use to do this type of optimization for the SSL virtual server?
A. SSL policy
B. TCP profile
C. Compression policy
D. Priority queuing policy
Why would an engineer want to specify a TCP Profile for a specific service group?
A. To enable use of features like SSL over TCP for that specific service group.
B. To adjust the TCP settings for traffic to and from that specific service group.
C. To use a specific SNIP for traffic to the back-end servers in that service group.
D. To enable features like use source IP, TCP keep alive and TCP buffering for a specific service group.
Scenario: For security reasons, the NSIP needs to be configured to only be accessible on interface 0/1,
which is VLAN 300.
The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.
How would the network engineer achieve this configuration?
A. set ns config -nsvlan 300 -ifnum 0/1
B. set ns ip 10.110.4.254 -gui ENABLED -vrID 300
C. add vlan 300 set ns ip 10.110.4.254 -mgmtAccess ENABLED
D. set ns config -IPAddress 10.110.4.254 -netmask 255.255.255.0
Scenario: An engineer executes the following commands:
add vlan 2 bind vlan 2 -ifnum 1/2
add ns ip 10.110.4.200 255.255.255.0
bind vlan 2 -IPAddress 10.110.4.200 255.255.255.0 What type of IP address has been added to the NetScaler?
A. VIP address
B. NSIP address
C. SNIP address
D. GSLB Site IP address
Scenario: A network engineer created an IPv6 virtual server on the NetScaler. The virtual server is using a service group with two IPv4 servers bound to it. When testing access to the virtual server from a client configured with an IPv6 address, he is unable to connect.
What could be the reason for this issue?
A. The NetScaler is disabled for NAT.
B. IPv6 protocol translation is disabled.
C. An IPv6 address on the NetScaler is not bound to the correct VLAN.
D. The NetScaler does not have an INAT rule to convert IPv4 to IPv6 from the back-end servers.
Scenario: A NetScaler engineer needs to enable access to some web servers running on an IPv6 only network. The clients connecting the services are on an IPv4 network. The engineer has already enabled IPv6 on the NetScaler.
What does the engineer need to do in order to provide access to the services on the IPv6 network?
A. Create an IPv6 tunnel and a IPv4 virtual server.
B. Configure an IPv6 VLAN and bind the required interface.
C. Create a IPv4 virtual server and bind the service group to it.
D. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.
A network engineer has configured two NetScaler MPX appliances as a high availability (HA) pair.
What can the engineer configure to prevent failover if only a single interface fails?
A. FIS
B. PBR
C. SNMP
D. VMAC
Scenario: The NetScaler has connections to a large number of VPNs. The network engineer wants to minimize the number of ARP requests.
Which feature should the network engineer enable to minimize ARP requests?
A. TCP Buffering
B. Use Source IP
C. Edge Configuration D. MAC based forwarding
When a network engineer logs onto a new NetScaler device in the London datacenter, data output indicates that the device is NOT configured for the local time.
How can the network engineer synchronize the correct time with an NTP server in the local data center?
A. Configure the correct time from the GUI and restart.
B. Modify the ntp.conf and rc.netscaler files and restart.
C. Logon using the nsrecover/nsroot credentials and restart.
D. Configure the NetScaler as a secondary NTP server and restart.
An engineer has two NetScaler devices in two different datacenters and wants to create a high availability (HA) pair with the two devices, even though they are on two different subnets.
How can the engineer configure the HA Pair between the two NetScaler devices?
A. Configure StaySecondary on the second datacenter appliance.
B. Ensure that INC mode is enabled during the creation of the HA Pair.
C. Enable the HAMonitors on all interfaces after the HA Pair has been created.
D. Change the NSIP of the second appliance to be on the same subnet as the first appliance.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Citrix exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 1Y0-351 exam preparations and Citrix certification application, do not hesitate to visit our Vcedump.com to find your solutions here.