1. Home
  2. Fortinet
  3. NSE7_EFW-6.4

Fortinet NSE 7 - Enterprise Firewall 6.4

Exam Details

  • Exam Code
    :NSE7_EFW-6.4
  • Exam Name
    :Fortinet NSE 7 - Enterprise Firewall 6.4
  • Certification
    :Fortinet Certifications
  • Vendor
    :Fortinet
  • Total Questions
    :122 Q&As
  • Last Updated
    :Jun 17, 2025

Fortinet Fortinet Certifications NSE7_EFW-6.4 Questions & Answers

  • Question 71:

    Which two tasks are automated using the Install Wizard on FortiManager? (Choose two.)

    A. Installing configuration changes to managed devices

    B. Importing interface mappings from managed devices

    C. Adding devices to FortiManager

    D. Previewing pending configuration changes for managed devices

  • Question 72:

    How does FortiManager handle FortiGuard requests from FortiGate devices, when it is configured as a local FDS?

    A. FortiManager can download and maintain local copies of FortiGuard databases.

    B. FortiManager supports only FortiGuard push to managed devices.

    C. FortiManager will respond to update requests only if they originate from a managed device.

    D. FortiManager does not support rating requests.

  • Question 73:

    View the exhibit, which contains the output of a debug command, and then answer the question below.

    Which of the following statements about the exhibit are true? (Choose two.)

    A. In the network on port4, two OSPF routers are down.

    B. Port4 is connected to the OSPF backbone area.

    C. The local FortiGate's OSPF router ID is 0.0.0.4

    D. The local FortiGate has been elected as the OSPF backup designated router.

  • Question 74:

    What is the diagnose test application ipsmonitor 99 command used for?

    A. To enable IPS bypass mode

    B. To provide information regarding IPS sessions

    C. To disable the IPS engine

    D. To restart all IPS engines and monitors

  • Question 75:

    What conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

    A. IP addresses are in the same subnet.

    B. Hello and dead intervals match.

    C. OSPF IP MTUs match.

    D. OSPF peer IDs match.

    E. OSPF costs match.

  • Question 76:

    Refer to the exhibit, which contains partial outputs from two routing debug commands.

    Why is the port2 default route not in the second command's output?

    A. It has a higher priority value than the default route using port1.

    B. It is disabled in the FortiGate configuration.

    C. It has a lower priority value than the default route using port1.

    D. It has a higher distance than the default route using port1.

  • Question 77:

    Which of the following conditions must be met for a static route to be active in the routing table? (Choose three.)

    A. The next-hop IP address is up.

    B. There is no other route, to the same destination, with a higher distance.

    C. The link health monitor (if configured) is up.

    D. The next-hop IP address belongs to one of the outgoing interface subnets.

    E. The outgoing interface is up.

  • Question 78:

    View the IPS exit log, and then answer the question below.

    # diagnose test application ipsmonitor 3 ipsengine exit log"

    pid = 93 (cfg), duration = 5605322 (s) at Wed Apr 19 09:57:26 2017 code = 11, reason: manual What is the status of IPS on this FortiGate?

    A. IPS engine memory consumption has exceeded the model-specific predefined value.

    B. IPS daemon experienced a crash.

    C. There are communication problems between the IPS engine and the management database.

    D. All IPS-related features have been disabled in FortiGate's configuration.

  • Question 79:

    View the exhibit, which contains a screenshot of some phase-1 settings, and then answer the question below.

    The VPN is up, and DPD packets are being exchanged between both IPsec gateways; however, traffic cannot pass through the tunnel. To diagnose, the administrator enters these CLI commands:

    However, the IKE real time debug does not show any output. Why?

    A. The debug output shows phases 1 and 2 negotiations only. Once the tunnel is up, it does not show any more output.

    B. The log-filter setting was set incorrectly. The VPN's traffic does not match this filter.

    C. The debug shows only error messages. If there is no output, then the tunnel is operating normally.

    D. The debug output shows phase 1 negotiation only. After that, the administrator must enable the following real time debug: diagnose debug application ipsec -1.

  • Question 80:

    Refer to the exhibit, which contains the output of diagnose sys session list.

    If the HA ID for the primary unit is zero (0), which statement about the output is true?

    A. This session cannot be synced with the slave unit.

    B. The inspection of this session has been offloaded to the slave unit.

    C. The master unit is processing this traffic.

    D. This session is for HA heartbeat traffic.

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Fortinet exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NSE7_EFW-6.4 exam preparations and Fortinet certification application, do not hesitate to visit our Vcedump.com to find your solutions here.