NetApp Netapp Other Certification NS0-173 Questions & Answers

• Question 11:

  After you install a FlexPod infrastructure at a customer site, you need to migrate the existing Vmware virtual machines off the infrastructure that was used before FlexPod was installed.

  Which VMware vSphere feature accomplishes this task?

  A. vMotion

  B. vSphere DRS

  C. VM Component Protection

  D. vSphere HA

  Correct Answer: A

• Question 12:

  Which Cisco Nexus series switch supports NX-OS standalone mode or Application Centric Infrastructure (ACI) fabric mode?

  A. Nexus 7000

  B. Nexus 3000

  C. Nexus 9000

  D. Nexus 5000

  Correct Answer: C

  Reference: https://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series-switches/guidec07-733228.html

• Question 13:

  You are configuring Cisco UCS servers for FC SAN boot and want to perform zoning on your Cisco Nexus 5000 series switches.

  In this scenario, which statement is correct?

  A. The corresponding FC ports on your NetApp storage array must be configured in LACP mode.

  B. An iSCSI license on the NetApp storage controller is required.

  C. SAN links are required between the Cisco Fabric Interconnects and the Nexus 5000 switches.

  D. FC zoning on the Nexus series switches is not supported; zoning can be done only on the Cisco Fabric Interconnects.

  Correct Answer: D

  Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-2/ b_UCSM_GUI_Configuration_Guide_2_2/b_UCSM_GUI_Configuration_Guide_2_2_chapter_011011.html

• Question 14:

  You are asked to design a FlexPod solution that meets the minimum requirements and includes Application Centric Infrastructure (ACI).

  Which three Cisco components are required in this scenario? (Choose three.)

  A. Cisco UCS B-Series servers

  B. Cisco Nexus 9000 Series switches

  C. Cisco Nexus 2000 Series Fabric Extender

  D. Cisco Nexus 3000 Series switches

  E. Cisco UCS Series Fabric Interconnects

  Correct Answer: ABE

  Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/UCS_CVDs/ flexpod_esxi55u2_n9k_aci_aff8040_design.html

• Question 15:

  A customer has ordered a FlexPod Select solution with a NetApp EF570.

  In this scenario, which three storage protocols are available for use? (Choose three.)

  A. InfiniBand

  B. CIFS

  C. iSCSI

  D. NFS

  E. FC

  Correct Answer: BDE

• Question 16:

  A customer is planning to use a pair of MDS switches in a FlexPod design to host a few SAN workloads.

  In this scenario, which two features should be enabled on the MDS switches for a successful configuration? (Choose two.)

  A. NPIV

  B. NPV

  C. port-channel-trunk

  D. fport-channel-trunk

  Correct Answer: AC

• Question 17:

  A customer has verified physical connectivity on the FlexPod. However, the LUNs are not available on the Cisco UCS server. To make the LUNs visible to the UCS, the customer must enable a switching feature for zoning.

  In this scenario, what should the customer do?

  A. Enable NPIV on all switches.

  B. Enable Spine mode on all the Cisco Nexus 9000 switches.

  C. Enable NPV on all switches.

  D. Enable the device connector feature in Cisco UCS Manager.

  Correct Answer: D

• Question 18:

  A client has a FlexPod Datacenter solution with four active fabric links in port channel mode established between the Cisco Fabric Interconnects and the IOMs on a Cisco 5108 blade chassis. The blade chassis is fully populated with Cisco UCS B200M5 blades. A worker in the data center inadvertently unplugs the fourth uplink cable from IOM-A while working in the rack.

  In this scenario, what happens to the network traffic?

  A. Connectivity for servers 3, 4, 7, and 8 all fail over to IOM-B.

  B. There is a loss of connectivity for servers 4 and 8.

  C. Traffic is load-balanced within IOM-A.

  D. Traffic is load-balanced within IOM-B.

  Correct Answer: A

• Question 19:

  A customer is planning to deploy a FlexPod solution for a large scale SAN requirement that uses the FC protocol. The customer plans to use Smart Zoning in the configurations to reduce the number of TCAM entries in the zoning process.

  In this scenario, which design would enable the customer to use Smart Zoning?

  A. storage connected to Cisco Nexus 9000 Series switches

  B. storage connected to Cisco Nexus 5000 Series switches

  C. storage connected to Cisco MDS switches

  D. storage directly connected to Cisco UCS Fabric Interconnects

  Correct Answer: C

  Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/UCS_CVDs/ flexpod_datacenter_vmware_netappaffa_design.html#_Toc23952741

• Question 20:

  What are characteristics of the Cisco UCS 5108 blade chassis?

  A. 4 RU, 6 half-width UCS B-Series blades, 160 Gbps I/O bandwidth

  B. 6 RU, 8 half-width UCS B-series blades, 160 Gbps I/O bandwidth

  C. 6 RU, 6 half-width UCS B-series blades, 80 Gbps I/O bandwidth

  D. 4 RU, 8 half-width UCS B-series blades, 40 Gbps I/O bandwidth

  Correct Answer: B

  Reference: https://www.cisco.com/c/dam/en/us/products/collateral/servers-unified-computing/ucs-b-seriesblade-servers/spec_sheet_c17-644224.pdf