Nutanix NCP-5.10 Online Practice Questions and Exam Preparation

Nutanix NCP-5.10 Online Questions & Answers

• Question 71:

  Which best practice should be followed when creating a bond in a Nutanix cluster?

  A. Place NICs of different speeds within the same bond
  B. Configure the bond to use LACP
  C. Only utilize NICs of the same speed within the same bond
  D. Use the default bond configuration after installation
  B. Configure the bond to use LACP

• Question 72:

  An administrator has a 3-node Nutanix cluster. The administrator stores critical data on a VM that runs on the cluster. Data must still be available through two host failures. Which three configuration steps must the administrator take to meet this requirement? (Choose three.)

  A. Add 3 nodes to the cluster.
  B. Convert the cluster from RF2 to RF3.
  C. Convert the containers from RF2 to RF3.
  D. Enable Compression for more space.
  E. Increase CVM memory to 24GB.
  A. Add 3 nodes to the cluster.
  B. Convert the cluster from RF2 to RF3.
  C. Convert the containers from RF2 to RF3.

• Question 73:

  A customer wants to isolate a group of VMs within their Nutanix environment for security reasons. The customer creates a VM with two NICs to act as a firewall and installs the appropriate software and certificates. However, no one from the outside can access the application.

  What is the likely cause of this problem?

  A. A shared volume group must be used by all isolated VMs
  B. More than one NIC cannot be added to a VM
  C. One of the NICs needs to be configured on the internal VLAN
  D. Wireshark is installed on the NAT VM
  C. One of the NICs needs to be configured on the internal VLAN

• Question 74:

  An administrator wants to secure an application running on an AHV cluster by limiting incoming and outgoing traffic destinations. The administrator creates a security policy for the application. What is the next step?

  A. Apply the security policy.
  B. Create an isolation policy.
  C. Add the security policy to an existing isolation policy.
  D. Restart the VM hosting application.
  A. Apply the security policy.

• Question 75:

  Refer to the exhibit.

  

  An administrator logs in to Prism Element, goes to the Network view, and sees the output shown in the exhibit. Which three steps must the administrator take to increase throughput to the host? (Choose three.)

  A. Change the VLAN ID to a higher priority ID
  B. Connect the 10Gb interfaces to the physical switch
  C. Remove any 1Gb interfaces still connected from the default bond
  D. Change the bond mode to balance-slb or balance-tcp
  E. Add a new switch to the network and connect 1Gb interfaces to it
  A. Change the VLAN ID to a higher priority ID
  B. Connect the 10Gb interfaces to the physical switch
  D. Change the bond mode to balance-slb or balance-tcp

• Question 76:

  What is Prism Central primarily used for?

  A. Multi-cluster network configuration
  B. Container creation
  C. Multi-cluster Single Sign On
  D. Data reduction configuration
  A. Multi-cluster network configuration

• Question 77:

  An administrator needs to move a Nutanix host from one cluster to another.

  Which step should the administrator take after evacuating VMs from the host to be moved?

  A. From the Task menu in Prism, select Cluster details, then un-check the host from the list.
  B. In Prism, highlight the host in the Hardware pane and select Remove Host.
  C. In Prism, highlight the host in the Hardware pane and select Remove from Metadata Ring.
  D. From the Task menu in Prism, select Licensing, then delete the host license.
  B. In Prism, highlight the host in the Hardware pane and select Remove Host.

• Question 78:

  What is the expected operation during node addition when the new node has a different AOS version?

  A. The node is automatically re-imaged using the software currently running in the cluster
  B. The node is added and a separate upgrade operation must be performed
  C. The entire cluster is upgraded to the latest one-click release
  D. The addition fails and forces the administrator to image using standalone Foundation
  D. The addition fails and forces the administrator to image using standalone Foundation

• Question 79:

  When creating a VM on an AHV cluster, how is the initial placement of the VM determined?

  A. AHV uses a round robin algorithm, placing new VMs onto hosts based on the numerical order of their UUID
  B. The administrator right clicks on the desired host and selects Power on VM from the dropdown menu
  C. The Acropolis Dynamic Scheduler selects a host which provides adequate resources for the VMs configuration
  D. Placement is determined by the host that holds the new_VM token at the time of VM creation
  C. The Acropolis Dynamic Scheduler selects a host which provides adequate resources for the VMs configuration

• Question 80:

  Which change can be made on a cluster with software-based Data-at-Rest Encryption enabled?

  A. Disable encryption on the cluster
  B. Deploy an additional Native KMS Server
  C. Enable encryption for a VM
  D. Change Native KMS to External KMS
  C. Enable encryption for a VM