HP HP0-J65 Online Practice Questions and Exam Preparation

HP HP0-J65 Online Questions & Answers

• Question 161:

  When setting up a single switch fabric, you realize that none of the servers can access any of the attached storage subsystem units. Which switch command should you use to verify whether or not zoning is enabled?

  A. aliasShow B. cfgShow
  C. configShow
  D. fabricShow
  B

• Question 162:

  A typical Fibre Channel transmission (based on a Class 3 connection) makes _____ trip(s) over the fiber.

  A. two
  B. four
  C. eight
  D. one
  B. four

• Question 163:

  When considering a SAN design for a customer what benefit is achieved by minimizing the number of hops between switches where many devices share a single-switch ISL?

  A. Selection Storage Presentation in a single SAN
  B. Centralized Manageability
  C. Oversubscription reduction
  D. Data locality and performance
  C. Oversubscription reduction

• Question 164:

  You are proposing an HP StoreVirtual 4000 cluster solution involving many LUNs. You need to minimize the number of iSCSI session for news hosts while using all paths for load balancing. Which multipathing configuration should you include in your proposal?

  A. HP DSM for MPIO with round robin load balancing
  B. MS DSM for MPIO with round robin load balancing
  C. MS DSM with shortest queue service time load balancing
  D. HP DSM for MPIO with no load balancing
  B. MS DSM for MPIO with round robin load balancing

• Question 165:

  What should you do to check supportability and maximum configuration, when mixing different generation of brocade switches?

  A. HPStorageWorks SAN Components Compatibility Guide
  B. HPStorageWorks Fabric Deployment Release Notes
  C. HPStorageWorks SAN Design Reference Guide
  D. HPStorageWorks Switch Installation Manual
  C. HPStorageWorks SAN Design Reference Guide

• Question 166:

  Which information should be included in the topology map documentation of a SAN design provided to your support organization? (Select two.)

  A. serial numbers of connected servers
  B. SAN switch zoning configurations
  C. storage controller operating mode parameters
  D. IP addresses of the connected servers
  E. World Wide Names of all nodes and devices
  B. SAN switch zoning configurations
  E. World Wide Names of all nodes and devices

• Question 167:

  You are connecting storage, servers and tape libraries in the same SAN fabric. What is the best practice for designing this environment? (Select two.)

  A. Create a second zone for the HBA and associated tape devices only if the host runs Windows.
  B. Create an additional zone for the HBA and associated tape devices.
  C. Ensure each zone includes both host HBAs and each target device is added to the zone.
  D. Create only one zone that includes both the HBA and associated tape devices.
  E. Ensure each zone has only one HBA (initiator) and each target device is added to the zone.
  B. Create an additional zone for the HBA and associated tape devices.
  E. Ensure each zone has only one HBA (initiator) and each target device is added to the zone.

• Question 168:

  You are designing a storage solution for a customer who wants to simplify SAN management by create blades will meet these requirements?

  A. HP StoreFabric 8/24 Bundled FC Switch
  B. HP 8Gb Simple SAN connection Kit
  C. HP Virtual Connect FlexFabric
  D. HP 6Gb SAS Switch Singel pack for HP BladeSystem c-Class
  C. HP Virtual Connect FlexFabric

• Question 169:

  What is the final phase when planning an HP SAN solution?

  A. Perform a SAN architecture and situation assessment.
  B. Document the availability, performance, and management requirements.
  C. Document the deployment strategy and obtain customer signoff.
  D. Select the best-fit HP supported SAN topology.
  C. Document the deployment strategy and obtain customer signoff.

• Question 170:

  You are presenting a solution to a customer that allows the current legacy distributed storage environment to be changed to a scalable shared storage design. Which feature of HP supported SAN solutions should you emphasize?

  A. Availability
  B. Security
  C. Modularity
  D. Business continuity
  C. Modularity