Huawei H13-341 Online Practice Questions and Exam Preparation

Huawei H13-341 Online Questions & Answers

• Question 1:

  Which of the following is the client-side logical port of a board in standard mode?

  A. ODUkLP-n
  B. RX/TX-n
  C. ClientLP-n
  D. n(Nn/OUTn)-OCH:1-ODUk:m-ODUp:q
  B. RX/TX-n

• Question 2:

  The OD system monitors the main optical path performance in each optical multiplexing section (OMS), which of the following items are monitored?

  A. whether the line loss exceeds the design end of life (EOL) value
  B. whether a fiber cut occurs on the main optical path.
  C. whether the optical power of the transmit-end OA board is out of the permitted range.
  D. whether the line loss compensation is out of the permitted range.
  A. whether the line loss exceeds the design end of life (EOL) value

• Question 3:

  Which of the following statements about the Service Package is incorrect?

  A. You can configure service package in two modes. One is to configure boards in batches, and the other is to configure each board.
  B. Service package enables one-click configuration of typical services by issuing multiple configuration commands in batches, facilitating product deployment commissioning and reducing maintenance costs.
  C. The Service Package can configure the working mode, service type, cross-connection, and port type in batches.
  D. Currently, Service Package is available to the TOA, TOX and TSC boards.
  D. Currently, Service Package is available to the TOA, TOX and TSC boards.

• Question 4:

  Which of the following signals can be used as input or output signals of an external clock interface?

  A. 2.048 MHz
  B. 2.048 Mbit/s
  C. 155 Mbit/s
  D. 34 Mbit/s
  A. 2.048 MHz

• Question 5:

  Which of the following statements about replacing the SCC board is incorrect?

  A. In the case of the 1+1 hot backup of the SCC board, replacing the control board does not affect services when the active/standby switchover is performed.
  B. After the SCC board is removed, the BD_STATUS and COMMUN_FAIL alarms are reported. After the new board goes online, these alarms need to be manually cleared.
  C. If the software version of the new SCC board is later than equipment version, clear the database of the SCC board, and then downgrade the software on the SCC board to the same version as the equipment.
  D. If the software version of the new SCC board is earlier than the equipment version, upgrade the software on the SCC board to the same version as the equipment.
  C. If the software version of the new SCC board is later than equipment version, clear the database of the SCC board, and then downgrade the software on the SCC board to the same version as the equipment.

• Question 6:

  Which of the following statements about avoiding the generation of discrete trails are correct?

  A. Use the trail function for configuration.
  B. For services configured on a per-NE basis, search for trails on the NMS to ensure that the service configurations are complete and standard.
  C. A fiber cut or switching test must be performed on the trail with protection routes to ensure that the configuration is complete and standard.
  D. Guide users to learn service configuration specifications.
  C. A fiber cut or switching test must be performed on the trail with protection routes to ensure that the configuration is complete and standard.

• Question 7:

  Which of the following methods can be used to analyze faults in the NG WDM system?

  A. Loopback
  B. Service Signal Flow Analysis
  C. RMON
  D. Replacement
  D. Replacement

• Question 8:

  In the case of the OptiX OSN equipment, when the standby board is normal, which of the following operations does not cause the active/standby switching of the cross-connect board or clock board?

  A. Delete the active cross-connect board or clock board logically.
  B. Open the upper and lower ejector levers of the active board at the same time.
  C. Deliver the active/standby switchover command.
  D. Perform a cold reset on the cross-connect or clock board.
  A. Delete the active cross-connect board or clock board logically.

• Question 9:

  Which of the following OTN trails does not need to be manually configured on an ROADM site, and can search out directly?

  A. OSC
  B. OCh
  C. OMS
  D. OTS
  B. OCh

• Question 10:

  If the LED indicator value on the SCC board of the OSN 8800 T32 board is 11, which of the following is the subrack ID?

  A. Slave subrack 2
  B. Slave subrack 1
  C. Slave subrack 17
  D. Slave subrack 11
  C. Slave subrack 17