Take effect immediately after the Router ID of the OSPF process is modified ()
A. TrueThe network shown in the figure below. The administrator wants RTA to use a static router. Priority is given to sending data packets to RTB's LoopbackO interface through G0/0/1 port. At the same time, G0/0/2 is used as a backup. Then any configuration on RTA can be Realize this requirement? () (Single-choice question)

All four switches run STP, and various parameters adopt default values. If the G0/0/2 port of switch C is blocked and the configuration BPDU cannot be sent through this port, how long will the blocked port in the network enter the forwarding state ()
A. About 50 secondsAccording to the VTY user interface configuration shown in the following figure, the user level is set to 3. [Huawei]user-interface vty 0 14 [Huawei-ui-vty0-14]acl 2000 inbound [Huawei-ui-vty0-14]user privilege level 3 [Huawei-ui-vty0-14]authentication-node password
Please configure the login password (maximum length 16): huawei
A. TrueWhat is the protocol number of OSPF at the network layer?
B. 1As shown in the figure, when the switch needs to forward frames with the destination mac address of 5489-98ec-f011, which of the following descriptions is correct? () (Single-choice question)

The output information of the sub-interface of a certain router's aggregation port 1 is shown in the figure. Based on this information, which of the following statements is correct? ( )
[Router A] display Interface Eth-Trunk 1.100Eth-Trunk1.100 current state UP Line protocol current state UP Last line protocol up time 2019-03-04 10:22:40 UTC.-08:00 Description:
HUAWEI, ARSeries, Eth-Trunk1.100 Interface Route Port, Hash arithmetiC.:According to SIP-XOR-DIP, Maximal BW:2G.Current BW:2G, The Maximum Transmit Unit is 1500 Internet Address is 10.0.12.2/24 IP Sending Frames'Format is
PKTFIT ETENT 2, Hardwareaddress 1s 00e0-fc3b-2015 Current system time:2019-03-04 10:24:29-08:00 Last 300 seconds input rate0 bits/sec.0 packets/sec Last 300 seconds output rate 0 bits /seC.0 packets/sec Realtime 0 seconds
inputrate 0 bits/seC.0 packets/sec Realtime 0 seconds output rate 0 bits/seC.0 packets/sec Input: 6 packets, 574 bytes,
Output: 7 packets, 638 bytes, Input bandwidth utilization 0% Output bandwidth utilization 0%
PortName Status Weight
GigabitEthernet0/0/1 UP 1 GigabitEthernet0/0/2 UP 1
The Number of Ports in Trunk:2 The Number of UP Ports in Trunk:2*
A. Two links exist on the aggregated portWhich of the following statements about the default route are correct? ()
A. If the destination address of the message cannot match any other routing entries in the routing table, the router will forward the message according to the default routeIf the network address of a network is 10.1.1.0/30, what is its broadcast address? ()
A. 10.1.1.3The static MAaddress table will not be lost after the system restarts ()
A. TrueNowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Huawei exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your H12-811 exam preparations and Huawei certification application, do not hesitate to visit our Vcedump.com to find your solutions here.