IBM C4040-221 Online Practice Questions and Exam Preparation

IBM C4040-221 Online Questions & Answers

• Question 31:

  Given the NIB configuration shown below, what is the most likely reason that after a link failure for ent0, there was no automatic failover to ent2?

  

  A. Alternate Address is not set
  B. No Internet Address to Ping is specified
  C. Automatically Recover to Main Channel is set to yes
  D. ent0 and ent2 have different media speeds specified
  B. No Internet Address to Ping is specified

• Question 32:

  The nmon output below illustrates typical load when the hosted application is running at peak times. What can be observed from the output?

  

  A. Entitled CPU allocation is set too high.
  B. Virtual processor allocation is set too low.
  C. Enabling SMT4 would improve performance.
  D. Processor folding is restricting available resources
  A. Entitled CPU allocation is set too high.

• Question 33:

  Which of the following is a supported source for creating a Versioned WPAR?

  A. An existing AIX 5.2 mksysb
  B. AIX 5.3 base product media
  C. An AIX 6.1 Global Environment
  D. NIM AIX 5.3 lpp_source and spot
  A. An existing AIX 5.2 mksysb

• Question 34:

  A failed integrated tape drive was physically replaced in a small P0WER7+ server. The administrator attempts to use the device and receives this error message:

  AN ERROR OCCURRED WHILE WRITING TO THE STORAGE MEDIA THE DEVICE IS NOT READY FOR OPERATION

  Which of the following is the most likely cause?

  A. The tape device microcode needs to be updated.
  B. The media inside the failed tape drive was not removed.
  C. The tape drive needs to be powered on before being used.
  D. The drive was replaced but the new device information was not configured
  D. The drive was replaced but the new device information was not configured

• Question 35:

  Which action must be completed on the HMC when a partition is in a Recovery state?

  A. Select Configuration and Restore partition data.
  B. Select Recover Partition Data for the managed system.
  C. Select Initialize Partition for the LPAR in Recovery state
  D. Select Configuration and Rebuild Managed System.
  B. Select Recover Partition Data for the managed system.

• Question 36:

  Consider the following information:

  

  A. 1310721
  B. 1376256
  C. 1311744
  D. 1310784
  B. 1376256

• Question 37:

  Which command, when issued from the HMC command line, will attempt to launch a virtual terminal session on Ipar1, running on the sys1 managed system?

  A. mkvterm-msys1 -p Ipar1
  B. crvterm-ssysy -r Ipar1
  C. startvt-h sys1 -I Ipar1
  D. startx-vt sys1 -p Ipar1
  A. mkvterm-msys1 -p Ipar1

• Question 38:

  Which Korn shell syntax is used to assign the directory of the called script to a variable called mydir?

  A. mydir=$(dirname $0)
  B. $mydir=$(dirname $0)
  C. mydir=${dirname $@}
  D. mydir=$(dirname $?)
  A. mydir=$(dirname $0)

• Question 39:

  What action will prevent the nfsd subsystem from activating at boot time?

  A. Update /etc/inetd.conf to remove the call to startsrc for the NFS subsystem group.
  B. Change the Action attribute from 'wait' to 'once' for the rcnfs line within the /etc/inittab.
  C. Remove the /etc/exports file.
  D. Amend the permissions of/etc/rc.tcpip file to remove execution rights.
  C. Remove the /etc/exports file.

• Question 40:

  When creating a new user id, an administrator encounters the following error message:

  aixsystem:/home/root# mkuser newuserid

  3004-694 Error adding "newuserid": Name is too long.

  Running which of the following commands will cause the mkuser newuserid command to complete successfully?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  A. Option A