A NetApp storage system running clustered Data ONTAP is logged in to an FC switch. An initiator logged in to the same switch. FCP is licensed, and the TCP service is created and running. The fcp initiator show command returns an empty table. What is the likely cause?
A. Target and initiator are NOT part of the same zone.
B. Initiator does NOT belong to an Igroup.
C. Igroup type does NOT match initiator OS type.
D. No LUNs are provisioned.
During a storage failover operation (SFO), a host accessing a LUN via the iSCSI protocol:
A. Will begin sending traffic over indirect paths.
B. Will begin sending traffic to a session already established to a logical interface on the HA partner.
C. Will establish a new session to the surviving node's partner interface and resume sending traffic.
D. Will establish a new session to the down node's HA partner and resume sending traffic
Which is NOT a correct igroup configuration?
A. Two different iQNs placed in different OS-type igroups and mapped to two different LUNs
B. Two different IQNs placed in an igroup and mapped to a single LUN
C. A single IQN placed in an igroup and mapped to a single LUN
D. A single IQN placed in two different OS-type igroups and mapped to a single LUN
A node's FC port is performing a Fabric Login however, the N_Port ID is not being virtualized. What is a likely cause?
A. NPIV was NOT enabled on the switch port.
B. ALUA was NOT enabled on the switch port.
C. ALUA was NOT enabled on the target port.
D. NPIV was NOT enabled on the initiator port.
For a Brocade Fibre Channel switch, which command can you use to check whether two devices zoned properly and whether connectivity exists?
A. Ping
B. Fcping
C. Check
D. Fccheck
E. Zone
F. Zonecheck
By default, what is allocation that the NetApp Unified Target Adapter uses between FCoE and other Ethernet traffic?
A. 25% FCoE; 75% other
B. 75% FCoE; 25% other
C. 100% FCoE; 0% other
D. 50% FCoE; 50% other
Which protocol does the FC Frame encapsulate within FCoE?
A. FCoE Frame
B. Ethernet
C. IP
D. SCSI-3
An FC port on a NetApp storage system running clustered Data ONTAP is connected to an FC switch. FCP is licensed on the cluster and the Vserver FCP service is created and running. The state of the FC LIF, which is bound to the port, is
administratively up and operationally down.
What is the likely cause?
A. Improper FC zone configuration
B. NPIV is not enabled on the switch
C. Improper igroup configuration
D. Bad cable
When running clustered Data ONTAP, which topology allows for guaranteed maximum network performance for iSCSI?
A. WAN network
B. VLAN network
C. MetroWAN network
D. Isolated VSAN network
The NetApp storage solution diagram for installation should include which three pieces of information (choose three.)
A. Power Feeds to all components to PDU's and UPS's
B. Floor tile grid for airflow for air conditioning
C. Path for movement of equipment in Data Center
D. Application storage usage by controller
E. Connectivity to switches - both Ethernet and FCP
F. Storage cabling, from the storage controllers to switches
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only NetApp exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NS0-504 exam preparations and NetApp certification application, do not hesitate to visit our Vcedump.com to find your solutions here.