Nokia 4A0-C01 Online Practice Questions and Exam Preparation

Nokia 4A0-C01 Online Questions & Answers

• Question 531:

  When configuring distributed services across a network, it is considered best practice to configure which of the following parameters as globally significant?

  A. Customer ID and SAP ID.
  B. Customer ID and Service ID.
  C. SAP ID and Service ID.
  D. SDP ID and Service ID.
  E. SDP ID and SAP ID.
  F. SDP ID and VC ID.
  B. Customer ID and Service ID.

• Question 532:

  A VPLS receives a frame with the single VLAN tag 35 on the Q-in-Q SAP 1/1/1:35.*. Which of the following describes default Alcatel-Lucent 7750 SR behavior?

  A. The frame is dropped.
  B. The VLAN tag is removed, and the frame is transported over the network.
  C. The VLAN tag is kept, and the frame is transported over the network.
  D. The VLAN tag is kept, a VLAN of 0 is added, and the frame is transported over the network.
  B. The VLAN tag is removed, and the frame is transported over the network.

• Question 533:

  In an OSPF environment, what must a router receive after it sends out an update?

  A. The router must receive an acknowledgment
  B. The router must receive a Hello
  C. The router must receive a new sequence number
  D. The router must receive a Link State Packet
  A. The router must receive an acknowledgment

• Question 534:

  A network consists of 4 PE routers. A customer requires a VPLS service and has sites connected to each PE. Each site must have direct connectivity with all other sites. How many SDPs must be configured on each PE?

  B. 2
  C. 3
  D. 4
  C. 3

• Question 535:

  The terms "customer" and "service" are used synonymously when describing a service implementation on the Alcatel-Lucent 7750 SR.

  A. TRUE
  B. FALSE
  B. FALSE

• Question 536:

  Which of the following about dot1Q SAPs is FALSE?

  A. The dot1Q default SAP (port: *) can be used to pass VLAN tags transparently through a network.
  B. The dot1Q null SAP (port: 0) accepts all tagged frames and untagged frames.
  C. The dot1Q default SAP (port: *) accepts all untagged frames and any frames with tag values that are not used as a service-delimiting value on another SAP.
  D. A dot1q null SAP (port: 0) and a dot1q default SAP (port: *) cannot both be defined on the same port.
  B. The dot1Q null SAP (port: 0) accepts all tagged frames and untagged frames.

• Question 537:

  Click on the exhibit.

  

  A service provider is deploying a 6 over 4 tunnel to connect a customer's corporate IPv6 network to all devices at the branch office as shown in the exhibit. Which command is used to create the route to the branch office network on PE1?

  A. Configure router static-route 2001:DB8:1:201::/64 indirect 10.10.10.4
  B. Configure router static-route 2001:DB8:1:201:764 indirect 2001:DB8:1:200::2
  C. Configure router static-route 2001:DB8:1:200::/56 indirect 10.10.10.4
  D. Configure router static-route 2001:DB8:1:200:756 indirect 2001:DB8:1:200::2
  C. Configure router static-route 2001:DB8:1:200::/56 indirect 10.10.10.4

• Question 538:

  An E-pipe is configured with a service MTU of 5000. What is the minimum MTU value that should be set on an access port for a dot1q encapsulated SAP on this service?

  A. 5000
  B. 5004
  C. 5008
  D. 5014
  B. 5004

• Question 539:

  Which of the following about SDPs is FALSE?

  A. An SDP is not required for a local service.
  B. A single SDP can carry different types of services.
  C. An SDP can simultaneously support GRE and MPLS encapsulation.
  D. An SDP can use the system IP address to indicate the far-end router.
  C. An SDP can simultaneously support GRE and MPLS encapsulation.

• Question 540:

  When provisioning a spoke-SDP on an Epipe, what MUST match on both ends of the service?

  A. Service ID
  B. Customer ID
  C. SAPID
  D. VC-ID
  E. SDPID
  D. VC-ID