Cisco 300-430 Online Practice Questions and Exam Preparation

Cisco 300-430 Online Questions & Answers

• Question 161:

  A network engineer is configuring a Cisco AireOS 8.2 WLC, Cisco MSE, and Cisco PI with Cisco 3700 Series APs and Cisco Hyperlocation modules. The engineer configures and enables a WLAN with Hyperlocation. During testing, the engineer notices that the Hyperlocation module cannot be seen on the WLC. Which action resolves the issue?

  A. Configure the APs to be in monitor mode.
  B. Enable Hyperlocation in the Global Configuration settings of the WLC.
  C. Add the key hash that is used to add the Hyperlocation module to the WLC.
  D. Enable the NTP server that is connected to the Hyperlocation module.
  B. Enable Hyperlocation in the Global Configuration settings of the WLC.

• Question 162:

  An engineer is implementing RADIUS to restrict administrative control to the network with the WLC management IP address of 192.168.1.10 and an AP subnet of 192.168.2.0/24. Which entry does the engineer define in the RADIUS server?

  A. administrative access defined on the WLC and the network range 192.168.2.0/255.255.254.0
  B. NAS entry of the virtual interface and the network range 192.168.2.0/255.255.255.0
  C. shared secret defined on the WLC and the network range 192.168.1.0/255.255.254.0
  D. WLC roles for commands and the network range 192.168.1.0/255.255.255.0
  C. shared secret defined on the WLC and the network range 192.168.1.0/255.255.254.0

  ---

  Explanation Explanation/Reference:

• Question 163:

  An engineer has configured the wireless controller to authenticate clients on the employee SSID against Microsoft Active Directory using PEAP authentication. Which protocol does the controller use to communicate with the authentication server?

  A. EAP
  B. 802.1X
  C. RADIUS
  D. WPA2
  C. RADIUS

• Question 164:

  Refer to the exhibit.

  

  A network administrator deploys the DHCP profiler service in two ISE servers: 10.3.10.101 and 10.3.10.102. All BYOD devices connecting to WLAN on VLAN63 have been incorrectly profiled and are assigned as unknown profiled endpoints. Which action efficiently rectifies the issue according to Cisco recommendations?

  A. Nothing needed to be added on the Cisco WLC or VLAN interface. The ISE configuration must be fixed.
  B. Disable DHCP proxy on the Cisco WLC.
  C. Disable DHCP proxy on the Cisco WLC and run the ip helper-address command under the VLAN interface to point to DHCP and the two ISE servers.
  D. Keep DHCP proxy enabled on the Cisco WLC and define helper-address under the VLAN interface to point to the two ISE servers.
  C. Disable DHCP proxy on the Cisco WLC and run the ip helper-address command under the VLAN interface to point to DHCP and the two ISE servers.

  ---

  Explanation Explanation/Reference:https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan- controllers/110865-dhcp- wlc.html

• Question 165:

  A company wants to switch to BYOD to reduce IT support costs for the company. Which option is an impact of BYOD should be considered?

  A. increased VPN connections
  B. restricted device enforcement
  C. increased phishing attacks
  D. decreased support calls
  A. increased VPN connections

• Question 166:

  A shopping center uses AireOS controllers with Cisco Wave 2 APs. A separate WLAN named Guest-012345678-WLAN is used for guest wireless clients. Management needs location analytics to determine popular areas. CMX must track only associated clients. What must be selected on the CMX server settings?

  A. Exclude probing clients
  B. Duty Cycle Cutoff
  C. Enable Locally Administered MAC Filtering
  D. Enable Location MAC Filtering
  A. Exclude probing clients

  ---

  Explanation Explanation/Reference:https://www.cisco.com/c/en/us/td/docs/wireless/mse/10-6/cmx_config/b_cg_cmx106/the_cisco_cmx_detect_and_locate_service.html#id_123333

• Question 167:

  You enter the command or a Cisco Catalyst 3850 Series Switch that runs Cisco ISO XE. What does the command do?

  A. It defines the user identity or the device identity to be validated by the RADIUS server.
  B. It captures information on the length of the authorized session, as well as the bandwidth usage of the client.
  C. It defines the RADIUS server used to track which sessions are still active.
  D. It defines the level of access of the user or the device.
  D. It defines the level of access of the user or the device.

• Question 168:

  Refer to the exhibit.

  

  An engineer is configuring a Cisco wireless LAN controller and needs wireless multicast to use the 54Mbps rates. Which action meets this requirement?

  A. Change the 24 Mpbs to Supported.
  B. Set all data rates below 54 Mbps to Supported.
  C. Change the 54 Mpbs to Mandatory.
  D. Set all data rates below 54 Mbps to Disable.
  C. Change the 54 Mpbs to Mandatory.

  ---

  Explanation Explanation/Reference: https://community.cisco.com/t5/wireless/wlc-settings-for-high-performance-cells/td-p/2298996#:~:text=The%20highest%20mandatory%20rate%20is,of%2018%20or%2024%20Mbps.

• Question 169:

  A Cisco WLC has been added to the network and Cisco ISE as a network device, but authentication is failing. Which configuration within the network device configuration should be verified?

  A. SNMP RO community
  B. device interface credentials
  C. device ID
  D. shared secret
  D. shared secret

• Question 170:

  In a Cisco WLAN deployment, it is required that all APs from branch 1 remain operational even if the control plane CAPWAP tunnel is down because of a WAN failure to headquarters. Which operational mode must be configured on the APs?

  A. Disconnected
  B. Connected
  C. Lightweight
  D. Standalone
  D. Standalone