VMware 2V0-602 Online Practice Questions and Exam Preparation

VMware 2V0-602 Online Questions & Answers

• Question 1:

  What two new features are introduced with virtual machine compatibility version 13? (Choose two.)

  A. IDE hot plug support
  B. VMXNET 4
  C. Virtual Memory maximum 6128 GB
  D. Virtual NVMe
  C. Virtual Memory maximum 6128 GB
  D. Virtual NVMe

• Question 2:

  You are editing the management network configuration of an ESXi 6.x Host from the vSphere Web Client. You mistakenly put the incorrect VLAN in place for the management network. What action do you need to take to correct this?

  A. You need to manually edit the configuration on the host with command line utilities.
  B. No action is required. By default ESXi rolls back configuration changes that disconnect the host.
  C. The ESXi host system configuration will need to be restored to the factory configuration to fix the issue.
  D. The change can be reverted in the vSphere Web Client by simply editing the switch again.
  B. No action is required. By default ESXi rolls back configuration changes that disconnect the host.

  ---

  By rolling configuration changes back, vSphere protects hosts from losing connection to vCenter Server as a result from misconfiguration of the management network. In this case, configuring the wrong VLAN on the management network would result in a lost connection to the server.

• Question 3:

  Which three actions are available in Troubleshooting Mode in the ESXi Direct Console User Interface (DCUI)? (Choose three.)

  A. Enable ESXi Shell.
  B. Modify DCUI idle timeout.
  C. Modify Password.
  D. Restart Management Network.
  E. Modify SSH timeout.
  A. Enable ESXi Shell.
  B. Modify DCUI idle timeout.
  E. Modify SSH timeout.

• Question 4:

  A VMware vSphere 6.x Administrator is tasked with configuring vRealize Log Insight. What three ports can be used for syslog? (Choose three.)

  A. 514/UDP
  B. 1514/TCP
  C. 8443/TCP
  D. 514/TCP
  E. 123/UDP
  A. 514/UDP
  B. 1514/TCP
  D. 514/TCP

• Question 5:

  Which type of Adapter does not require vmkernel networking?

  A. Independent Hardware iSCSI Adapter
  B. Dependent Hardware iSCSI Adapter
  C. Software iSCSI Adapter
  D. Software FCoE Adapter
  A. Independent Hardware iSCSI Adapter

• Question 6:

  What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?

  A. Users remain logged in and can run commands, except to disable lockdown mode.
  B. Users remain logged in and can run commands, including disabling lockdown mode.
  C. Users are immediately logged out of ESXi Shell.
  D. Users are logged out after a timeout specified by the vSphere administrator.
  A. Users remain logged in and can run commands, except to disable lockdown mode.

• Question 7:

  An IT administrator working in a space agency has just in installed some applications that are critical for a satellite launch mission. The administrator wants the applications to work irrespective of any operating system failure. Which vSphere

  6.x

  feature should the administrator use?

  A. vSphere HA
  B. vSphere Fault Tolerance
  C. vSphere Replication
  D. vSphere Data Protection
  B. vSphere Fault Tolerance

• Question 8:

  Which virtual switch load balancing method should be used when teaming network interfaces with EtherChannel?

  A. Route based on originating virtual port.
  B. Route based on IP hash.
  C. Route based on physical NIC load.
  D. Route based on source MAC hash.
  E. Use explicit failover order.
  B. Route based on IP hash.

• Question 9:

  An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the

  system.

  How can this be accomplished in the shortest amount of time?

  A. Run the ESXi installer again and reinstall the host.
  B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
  C. From the Direct Console User Interface, select Reset System Configuration.
  D. Use a host profile to reset the configuration to a default state.
  C. From the Direct Console User Interface, select Reset System Configuration.

• Question 10:

  Refer to the Exhibit. A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit.

  

  Which portgroup would be utilized by default when creating a new virtual machine?

  A. Access Network
  B. DMZ Network
  C. VM Network
  D. Virtual Machine Network
  A. Access Network

  ---

  The answer is Access Network because it selects the portgroup based on the first letter according to the alphabet