Citrix 1Y0-253 Online Practice Questions and Exam Preparation

Citrix 1Y0-253 Online Questions & Answers

• Question 131:

  Scenario: An administrator notices that each time the secondary node of a high availability (HA) pair is restarted, the primary node shifts to a non-working state. The administrator runs a command and collects the information displayed below: 1) Node ID. 0 IP: 172.31.250.10 Node StatE. NOT UP Master StatE. Secondary INCStatE.DISABLED Sync StatE. DISABLED Propagation: ENABLED Enabled Interfaces : 1j5 1j1 1j2 1j4 0j1 Disabled Interfaces : 1j3 HA MON ON Interfaces : 1j4 1j1 0j1 Interfaces on which heartbeats are not seen : 1j4 1j1 1j2 1j5 0j1 Interfaces causing Partial FailurE. 1j4 SSL Card Status: UP Hello Interval: 200 msecs DeadInterval:3secs Node in this Master State for: 0:0:0:35 (days:hrs:min:sec) 2) Node ID. 1 IP: 172.31.250.20 Node StatE. UNKNOWNjDOWN Master StatE. UNKNOWN INC StatE. UNKNOWN Sync StatE. UNKNOWN Propagation: UNKNOWN Enabled Interfaces : UNKNOWN Disabled Interfaces : UNKNOWN HA MON ON Interfaces : UNKNOWN SSL Card Status: UNKNOWN

  What could be the cause of this issue?

  A. Synchronization is disabled.
  B. The Hello Interval is set too high.
  C. One of the interfaces is disabled.
  D. One of the HA Monitoring interfaces is failing.
  D. One of the HA Monitoring interfaces is failing.

• Question 132:

  An administrator is reviewing the following output:

  vIP(141.128.58.149:80:UP:WEIGHTEDRR): Hits(38200495, 18jsec) Mbps(1.02) Pers(OFF) Err(0) Pkt(186jsec, 610 bytes) actSvc(4) DefPol(NONE) override(0)

  Conn: Clt(253, 1jsec, OE[252/]) Svr(3) S(141.128.49.40:80:UP) Hits(9443063, 4jsec, P[2602342, 0jsec]) ATr(5) Mbps(0.23)BWlmt(100 kbits) RspTime(112.58 ms)

  Other: Pkt(36jsec, 712 bytes) Wt(10000) RHits(31555)

  Conn: CSvr(42, 0jsec)MCSvr(20)OE(16)RP(11)SQ(0)

  How much traffic is being passed through the public IP address based on the output displayed above?

  A. 100 kbits
  B. 1.02 Mbps
  C. 0.23 Mbps
  D. 112.58 ms
  B. 1.02 Mbps

• Question 133:

  Which NetScaler IP address type is created when the below command is executed at the command-line interface?

  add ns ip 192.168.2.1 255.255.255.0

  A. virtual IP
  B. Cluster IP
  C. Subnet IP
  D. Mapped IP
  E. GSLB Site IP
  C. Subnet IP

• Question 134:

  Which log file should a Citrix Administrator use to troubleshoot a cluster node in the INACTIvE state?

  A. ns.log
  B. http.log
  C. auth.log
  D. nscollect.log
  A. ns.log

• Question 135:

  Scenario: Authentication through a NetScaler Gateway is NOT functioning for all users. A Citrix Administrator needs to ensure that user authentication events are being sent to the external corporate logging server. Where should the administrator go in the NetScaler Configuration Utility to meet this requirement?

  A. Policies > Auditing > Nslog
  B. Policies > Auditing > Syslog
  C. Policies > Authentication > Local
  D. Policies > Authentication > LDAP
  B. Policies > Auditing > Syslog

• Question 136:

  Which two actions should an administrator take to ensure the first NetScaler node configured in a high availability (HA) pair remains the primary node after a second node is added? (Choose two.)

  A. Set Stay Primary on the first node.
  B. Configure Stay Secondary on the second node.
  C. Enable HA Sync before adding the second node.
  D. Create a Route Monitor to ensure proper synchronization.
  E. Ensure that INC mode is enabled during creation of the HA pair.
  A. Set Stay Primary on the first node.
  B. Configure Stay Secondary on the second node.

• Question 137:

  Which command can a Citrix Administrator use to see a specific auditing Syslog policy binding?

  A. show log
  B. show audit
  C. show syslog
  D. show attribute
  B. show audit

• Question 138:

  Which IP address does NetScaler use for Active Directory authentication?

  A. virtual IP (vIP)
  B. Client IP (CIP)
  C. NetScaler IP (NSIP)
  D. Subnet IP (SNIP)
  D. Subnet IP (SNIP)

• Question 139:

  Which command-line interface command could an administrator use to display communication between the LDAP server and the NetScaler system?

  A. cat jetcjkrb5.conf
  B. cat jetcjkrb5.keytab
  C. cat jtmpjaaad.debug
  D. cat jvarjlogjaaad.debug
  E. tail -f jvarjlogjaaad.debug
  C. cat jtmpjaaad.debug

• Question 140:

  Scenario: Users report that they are being presented with a certificate error when they attempt to access the remote access website of the company. No changes were made to the NetScaler certificates recently. What should the Citrix Administrator check on the NetScaler to identify this issue?

  A. Cert Links
  B. OCSP Binding
  C. Certificate Format
  D. Certificate Expiry Date
  D. Certificate Expiry Date