Exam Details

  • Exam Code
    :EW0-200
  • Exam Name
    :Extreme Networks Associate (ENA)
  • Certification
    :Extreme Networks Certifications
  • Vendor
    :Extreme Networks
  • Total Questions
    :245 Q&As
  • Last Updated
    :Jun 28, 2025

Extreme Networks Extreme Networks Certifications EW0-200 Questions & Answers

  • Question 211:

    What is true when VLAN corporate shows a protocol field with the value of NONE.

    A. VLAN corporate will not forward any traffic.

    B. VLAN corporate must be a MAC-based VLAN.

    C. It is not possible for a VLAN to have NONE listed as the protocol.

    D. None of these.

  • Question 212:

    RIP is a routing protocol that scales to a limit. What is the maximum number of supported hop counts?

    A. 10

    B. 15

    C. 20

    D. 30

  • Question 213:

    In order to span multiple VLANs across Extreme switches, the protocol EDP must be enabled.

    A. TRUE

    B. FALSE

  • Question 214:

    After using the disable web command you later issue the show session command and see the following: How was it possible for someone to login with ExtremeWare Vista?

    A. Admin level accounts can always login through console, telnet, and HTTP.

    B. You did not reboot after issuing the DISABLE WEB command.

    C. You did not save the configuration after issuing the DISABLE WEB command.

    D. The disable web command does not exist.

  • Question 215:

    What information will the CLI Command how edp?provide?

    A. The EDP status of the local switch ports.

    B. The configured system names, Port numbers and VLANs of the remote Extreme switches

    C. The MAC address of the remote systems connected.

    D. All of the above

  • Question 216:

    What is the maximum number of simultaneously active protocol filters in the switch for all ?based Extreme switch products?

    A. 7

    B. 14

    C. 15

    D. None of these

  • Question 217:

    Which CLI command would you use to add a VLAN to a newly created STPD s1?

    A. config stpd s1 add vlan

    B. config s1 stpd add vlan

    C. config stpd add s1 vlan

    D. config s1 add stpd vlan

  • Question 218:

    What is the default value for the RIP garbage-time setting?

    A. 30 seconds

    B. 60 seconds

    C. 120 seconds

    D. 240 seconds

  • Question 219:

    In an Ethernet LAN, Layer 2 broadcasts reach every device within the same broadcast domain and may cause bandwidth, congestion and delay issues.

    A. TRUE

    B. FALSE

  • Question 220:

    In order to set the OSPF router ID to 192.168.0.1 in area 7.7.7.7 which of the following CLI commands should be used?

    A. config routerid ospf 192.168.0.1 area 7.7.7.7

    B. config ospf routerid 192.168.0.1

    C. config ospf 192.168.0.1 routerid area 7.7.7.7

    D. config 192.168.0.1 ospf routerid

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Extreme Networks exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your EW0-200 exam preparations and Extreme Networks certification application, do not hesitate to visit our Vcedump.com to find your solutions here.