Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 711:

  Refer to the exhibit. R1 and R2 are directly connected, but the BGP session does not establish.

  

  Which action must be taken to build an eBGP session?

  A. Configure ip route 1.1.1.1 0.0.0.0 192.168.12.1 on R2.
  B. Configure neighbor 192.168.12.1 activate under R2 BGP process.
  C. Configure neighbor 2.2.2.2 remote-as 65002 under R1 BGP process.
  D. Configure no neighbor 192.168.12.1 shutdown under R2 BGP process.
  D. Configure no neighbor 192.168.12.1 shutdown under R2 BGP process.

  ---

  Explanation

  References:

  https://www.noction.com/blog/debug-bgp-states#:~:text=Idle%20(Admin)%20means%20that%20the,!&text=This%20is%20a%20good%20way,BGP%20section%20of%20the%20configuration

• Question 712:

  What is a characteristic of a virtual machine?

  A. It must be aware of other virtual machines, in order to allocate physical resources for them
  B. It is deployable without a hypervisor to host it
  C. It must run the same operating system as its host
  D. It relies on hypervisors to allocate computing resources for it
  D. It relies on hypervisors to allocate computing resources for it

• Question 713:

  Into which two pieces of information does the LISP protocol split the device identity? (Choose two)

  A. Device ID
  B. Enterprise Identifier
  C. LISP ID
  D. Routing Locator
  E. Resource Location
  F. Endpoint Identifier
  D. Routing Locator
  F. Endpoint Identifier

  ---

  Explanation

  Locator ID Separation Protocol (LISP) is a network architecture and protocol that implements the use of two namespaces instead of a single IP address: + Endpoint identifiers (EIDs)--assigned to end hosts.

  + Routing locators (RLOCs)--assigned to devices (primarily routers) that make up the global routing system.

  References:

  https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_lisp/configuration/xe-3s/irl-xe-3s-book/irl-overview.html

• Question 714:

  Which action reduces sticky clients in dense RF environments?

  A. Decrease radio channel widths to 40 MHz.
  B. Increase the mandatory minimum data rates.
  C. Decrease the mandatory minimum data rates.
  D. Increase radio channel widths to 160 MHz.
  B. Increase the mandatory minimum data rates.

• Question 715:

  Which device makes the decision for a wireless client to roam?

  A. wireless client
  B. wireless LAN controller
  C. access point
  D. WCS location server
  A. wireless client

  ---

  Explanation

  References:

  https://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/Client_roaming_and_connectivity_decisions_explained

• Question 716:

  The Gig0/0 interface of two routers is directly connected with a 1G Ethernet link.

  Which configuration must be applied to the interface of both routers to establish an OSPF adjacency without maintaining a DR/BDR relationship?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  B. Option B

  ---

  Explanation

  cisco_R3#show run int e0/0.50

  Building configuration...

  Current configuration : 189 bytes

  !

  interface Ethernet0/0.50

  encapsulation dot1Q 50

  ip address 10.111.10.1 255.255.255.252 ip ospf network point-to-point <<<<<<<<<<<<<<<<<<< ip ospf 1 area 22 bfd interval 999 min_rx 999 multiplier 3 end

  cisco_R3#show ip ospf neighbor

  Neighbor ID Pri State Dead Time Address Interface 192.168.255.2 1 FULL/DROTHER 00:00:33 192.168.255.2 Ethernet0/0.10 200.200.200.200 1 FULL/DR 00:00:34 192.168.255.22 Ethernet0/0.10 5.5.5.5 0 FULL/ - 00:00:34 10.111.10.2

  Ethernet0/0.50 <<<<<<<<<<<<<<<<< cisco_R3#

• Question 717:

  DRAG DROP

  Drag and drop the Cisco Catalyst Center (formerly DNA Center) southbound API characteristics from the left to the right. Not all options are used.

  Select and Place:

  

  

• Question 718:

  An engineer is configuring RADIUS-Based Authentication with EAP. MS-CHAPv2 is configured on a client device.

  Which outer method protocol must be configured on the ISE to support this authentication type?

  A. EAP-TLS
  B. EAP-FAST
  C. LDAP
  D. PEAP
  D. PEAP

• Question 719:

  How does SSO work with HSRP to minimize network disruptions?

  A. It enables HSRP to elect another switch in the group as the active HSRP switch.
  B. It ensures fast failover in the case of link failure.
  C. It enables data forwarding along known routes following a switchover, white the routing protocol reconverges.
  D. It enables HSRP to failover to the standby RP on the same device.
  D. It enables HSRP to failover to the standby RP on the same device.

  ---

  Explanation

  SSO HSRP alters the behavior of HSRP when a device with redundant Route Processors (RPs) is configured for stateful switchover (SSO) redundancy mode. When an RP is active and the other RP is standby, SSO enables the standby RP to take over if the active RP fails. The SSO HSRP feature enables the Cisco IOS HSRP subsystem software to detect that a standby RP is installed and the system is configured in SSO redundancy mode. Further, if the active RP fails, no change occurs to the HSRP group itself and traffic continues to be forwarded through the current active gateway device.

  References:

  https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/15-s/fhp-15-sbook/fhp-hsrp-sso.html

• Question 720:

  An engineer must configure HSRP group 300 on a Cisco IOS router. When the router is functional, it must be the active HSRP router. The peer router has been configured using the default priority value.

  Which command set is required?

  A. standby version 2 standby 300 priority 110 standby 300 preempt
  B. standby 300 priority 110 standby 300 timers 1 110
  C. standby version 2 standby 300 priority 90 standby 300 preempt
  D. standby 300 priority 90 standby 300 preempt
  A. standby version 2 standby 300 priority 110 standby 300 preempt

  ---

  Explanation

  In HSRP version 1, group numbers are supported the range from 0 to 255 and HSRP version 2 expands the group number range from 0 to 4095.

  * So it should HSRP v2 to assign the group no. 300 (So. the ans should A or C).

  * Default priority of the HSRP is 100 and the Router with higher priority no. will become Active Router. So the priority set over 100 for active router.