Cisco CCNP 300-610 Questions & Answers

• Question 11:

  A company purchased a Cisco UCS system with four 5108 Chassis populated with UCS B-Series servers. The environment consists of nine Cisco HyperFlex rack servers. An engineer must provision virtual machines using an orchestration tool to optimize overall deployment time.

  Which orchestration must be used to meet this requirement?

  A. Cisco Intersight

  B. Cisco DNA Center

  C. Cisco AppDynamic

  D. Cisco Network Assurance

  Correct Answer: A

• Question 12:

  A company plans to implement high availability between the iSCSI host and the Fibre Channel target. Which solution must the company implement to recover from a failure of a host NIC. MDS IP storage port or Fibre Channel target port?

  A. Implement HSRPofi thf MDS IP storage ports

  B. Set up IP storage ports to export the two Fibre Channel target ports

  C. Map the Fibre Channel target ports to one IP storage port

  D. Configure FCoE between the host NICs and MDS ports

  Correct Answer: C

• Question 13:

  A data center uses Cisco Nexus 7000 Series Switch and contains two tenants, tenant A and tenant B.

  1.

  Tenant A uses IP addresses in the 10.2.30.41/24 to 10.2.30.64/24 range.

  2.

  Tenant B uses IP addresses in the 10.2.30.120/24 to 10.2.30.192/24 range. The engineer must implement a solution that:

  1.

  Isolates the traffic for each tenant as separate routing data and control planes.

  2.

  Physically partitions the Cisco Nexus device into separate multiple logical devices with separate management, failure domain isolation, and resource management. Which two technologies meet these requirements? (Choose two.)

  A. VDC

  B. vPC

  C. VXLAN

  D. VLAN

  E. VRF

  Correct Answer: AE

• Question 14:

  An engineer must design a Cisco UCS environment for a customer The design requires the most efficient use of available bandwidth with active-active uplinks The upstream Cisco Nexus 9000 Series Switch must automatically initiate the port-channel connectivity to the fabric interconnects Which configuration must the engineer choose to meet these requirements?

  A. ?fabric interconnects in Ethernet switching mode ?LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches

  B. ?fabric interconnects in Ethernet switching mode ?static port-channel from fabric interconnects and Cisco Nexus 9000 switches

  C. ?fabric interconnects in Ethernet end-host mode ?LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches

  D. ?fabric interconnects in Ethernet end-host mode ?static port-channel from fabric interconnects and Cisco Nexus 9000 switches

  Correct Answer: C

  Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Network-Mgmt/4-0/b_UCSM_Network_Mgmt_Guide_4_0/b_UCSM_Network_Mgmt_Guide_4_0_chapter_01 1.html Cisco UCS Fabric Interconnect in Switch Mode with Cisco MDS 9000 Family Fibre Channel Switching Modules When the Cisco UCS Fabric Interconnect is in switch mode, the port channel mode can only be in ON mode and not Active . However, to get the peer wwn information for the Fabric Interconnect, the port channel must be in Active mode.

• Question 15:

  Refer to the exhibit.

  

  Which template is used when a vHBA template pair is created for a specific server that inherits its attributes from an existing template?

  A. Secondary

  B. Initial

  C. Updating

  D. Primary

  Correct Answer: A

  https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Network-Mgmt/3-1/b_UCSM_Network_Mgmt_Guide_3_1/b_UCSM_Network_Mgmt_Guide_3_1_chapter_0111.html

  1.

  Secondary Template- All shared configurations are inherited from the Primary template.

  2.

  Initial Template: vNICs created from this template are not updated if the template changes.

  3.

  Updating Template: vNICs created from this template are updated if the template changes

• Question 16:

  A network engineer must design a Cisco HyperFlex solution based on these requirements:

  1.

  two clusters in the main data center consisting of five HyperFlex nodes

  2.

  one edge node for the remote branch

  3.

  cluster nodes that use one rack unit of space

  Which two devices should be used in the remote branch cluster for this design? (Choose two.)

  A. Gigabit Ethernet Switch

  B. HX240C

  C. HX220C

  D. Fabric Interconnect 6300

  E. UCSB B200

  Correct Answer: BE

• Question 17:

  Which orchestration tool provides a graphical interface to manage LAN and SAN fabrics?

  A. Cisco Virtual Topology System

  B. Cisco Data Center Network Manager

  C. Cisco Nexus Fabric Manager

  D. Cisco CloudCenter

  Correct Answer: B

  Reference:

  https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/DCNM_OLH/SAN_Client/fm help/fmc.html#34479

• Question 18:

  A Cisco engineer is developing a custom application that can run natively in Cisco NX-OS on Nexus 9000 and Nexus 3000 platforms For the NX-SDK application to run the engineer enables the NX-SDK feature on the device Then the NXSDK is imported into the application via an import nx_sdk_py statement. The engineer creates custom CLI commands and defines custom CLI command syntax within the sdkThread function

  When CLI commands originate from an NX-SDK application what class is this?

  A. clicm.printConsole

  B. postCliCb

  C. pyCmdhandler

  D. nx_sdk_pyValid-to_int

  Correct Answer: D

• Question 19:

  An engineer working for a private telecommunication company with an employee id 4298 53 420 must evaluate connectivity to the new data centre location based on Cisco Nexus 7000 Series Switches. The IP connectivity is already supplied by the service provider. The solution must provide a Layer 2 extension and optimize the traffic localization

  Which technology supports these requirements?

  A. IS-lS multi site over ACl

  B. VXLAN over EoMPLS

  C. OTV over IP and multicast

  D. BGP over VPLS

  Correct Answer: B

• Question 20:

  A network consultant reviews the requirements for the Storage Area Network (SAN) design. The proposed solution must offer a very efficient port usage and eliminate the need for a separate physical layer of switches and their associated ISLs. The design is not expected to require future expansion.

  Which SAN topology must be used to meet these requirements?

  A. core-edge

  B. collapsed-core

  C. core-distribution-access

  D. edge-core-edge

  Correct Answer: B