Which of the following is a characteristic of Packet switched network?
A. End-to-end connection establishment needed.
B. Fixed bandwidth.
C. Resources are requested on demand, more efficient use.
D. Charging is usually based on time.
In DX200 alarm printout, unknown equipment type is printed as?
A. SWITCH.
B. TRANSM.
C. EXTERN.
D. ???????.
Nokia is offering for Radio Access Technology, Remote SW Upgrade Services via RAS Server. Which is the Nokia preferred and cost efficient delivery channel for this service offering?
A. GSD.
B. NI.
C. Roll Out Support via Partners on Site.
D. All Nokia Lines of Businesses.
The Nokia Flexi Multiradio 10 Base Station supports:
A. GSM/EDGE, CDMA2000, WCDMA, HSPA and HSPA evolution, LTE TDD/FDD.
B. Supports 3GPP functions and features in 3GPP release 9 and beyond with modules open to Base Station Architecture Initiative (OBSAI) and Common Public Radio Interface (CPRI).
C. Flexi Multiradio 10 Base Station does not support the old legacy network interfaces. It is a true Ethernet-based transport with security BTS solution, synchronization and timing methods based on synchronous Ethernet, timing over packet, and GPS methods.
D. GSM/EDGE, WCDMA, HSPA and HSPA evolution, LTE TDD/FDD, NMP450.
Which is the IP based protocol in GPRS network?
A. GTP.
B. UDP.
C. PDCP.
D. SCTP.
What is the protocol used to transfer alarm between BSC and NetAct?
A. X.25.
B. LAPD.
C. Q3.
D. SCTP.
What is the minimum bit rate of Subtsl in the BSC?
A. 2.
B. 16.
C. 8.
D. 64.
What is Selective Cell?
A. Type of Umbrella Cells
B. Cell used to fill in a hole in the coverage of another Cells
C. Pico Cells used with Macro Cells
D. Micro Cells used with Pico Cells
Which of the following is NOT a GSM basic service?
A. Asynchronous data transmission for circuit switched with data rate of 9.600 bps.
B. Short message service.
C. Call forwarding.
D. Fax transmission.
How many BTS resets are possible in a Flexi Multiradio BTS GSM/EDGE?
A. BCF (site) reset: resets all modules/units in the site except transmission submodules (FIxx).BTS (sector) reset: resets a single BTS object, including all TRXs that are part of the BTS object configuration.System Module reset.
B. BCF (site) reset: resets all modules/units in the site except transmission submodules (FIxx).BTS (sector) reset: resets a single BTS object, including all TRXs that are part of the BTS object configuration.TRX reset: resets all configured TRX.OMU reset is not supported at all.System Module reset.
C. BCF (site) reset: resets all modules/units in the site except transmission submodules (FIxx).BTS (sector) reset: resets a single BTS object, including all TRXs that are part of the BTS object configuration.TRX reset: resets a single TRX.OMU reset: OMU is restarted.System Module reset.
D. BCF (site) reset: resets all modules/units in the site except transmission submodules (FIxx).BTS (sector) reset: resets a single BTS object, including all TRXs that are part of the BTS object configuration.TRX reset: resets a single TRX.OMU reset is not supported at all.System Module reset.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Nokia exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NCS_20022101010 exam preparations and Nokia certification application, do not hesitate to visit our Vcedump.com to find your solutions here.