Juniper Juniper Certifications JN0-332 Questions & Answers

• Question 241:

  You have been tasked with performing an update to the IDP attack database.

  Which three requirements are included as part of this task? (Choose three.)

  A. The IDP security package must be installed after it is downloaded.

  B. The device must be rebooted to complete the update.

  C. The device must be connected to a network.

  D. An IDP license must be installed on your device.

  E. You must be logged in as the root user.

  Correct Answer: ACD

• Question 242:

  Which statement is true regarding redundancy groups?

  A. The preempt option determines the primary and secondary roles for redundancy group 0 during a failure and recovery scenario.

  B. When priority settings are equal and the members participating in a cluster are initialized at the same time, the primary role for redundancy group 0 is assigned to node 1.

  C. The primary role can be shared for redundancy group 0 when the active-active option is enabled.

  D. Redundancy group 0 manages the control plane failover between the nodes of a cluster.

  Correct Answer: D

• Question 243:

  What are two interfaces created when enabling a chassis cluster? (Choose two.)

  A. st0

  B. fxp1

  C. fab0

  D. reth0

  Correct Answer: BC

• Question 244:

  What is a redundancy group in JUNOS Software?

  A. a set of chassis clusters that fail over as a group

  B. a set of devices that participate in a chassis cluster

  C. a set of VRRP neighbors that fail over as a group

  D. a set of chassis cluster objects that fail over as a group

  Correct Answer: D

• Question 245:

  When devices are in cluster mode, which new interfaces are created?

  A. No new interface is created.

  B. Only the st interface is created.

  C. fxp1, fab0, and fab1 are created.

  D. st, fxp1, reth, fab0, and fab1 are created.

  Correct Answer: C

• Question 246:

  Click the Exhibit button.

  [edit chassis]

  user@host# show

  cluster {

  reth-count 3;

  redundancy-group 1 {

  node 0 priority 1;

  node 1 priority 100;

  }}

  When applying the configuration in the exhibit and initializing a chassis cluster, which statement is correct?

  A. Three physical interfaces are redundant.

  B. You must define an additional redundancy group.

  C. node 0 will immediately become primary for redundancy group 1.

  D. You must issue an operational command and reboot the system for the above configuration to take effect.

  Correct Answer: D

• Question 247:

  You have been tasked with installing two SRX 5600 platforms in a high-availability cluster. Which requirement must be met for a successful installation?

  A. You must enable SPC detect within the configuration.

  B. You must enable active-active failover for redundancy.

  C. You must ensure all SPCs use the same slot placement.

  D. You must configure auto-negotiation on the control ports of both devices.

  Correct Answer: C

• Question 248:

  What are three benefits of using chassis clustering? (Choose three.)

  A. Provides stateful session failover for sessions.

  B. Increases security capabilities for IPsec sessions.

  C. Provides active-passive control and data plane redundancy.

  D. Enables automated fast-reroute capabilities.

  E. Synchronizes configuration files and session state.

  Correct Answer: ACE

• Question 249:

  Regarding secure tunnel (st) interfaces, which statement is true?

  A. You cannot assign st interfaces to a security zone.

  B. You cannot apply static NAT on an st interface logical unit.

  C. st interfaces are optional when configuring a route-based VPN.

  D. A static route can reference the st interface logical unit as the next-hop.

  Correct Answer: D

• Question 250:

  Which two configuration elements are required for a route-based VPN? (Choose two.)

  A. secure tunnel interface

  B. security policy to permit the IKE traffic

  C. a route for the tunneled transit traffic

  D. tunnel policy for transit traffic referencing the IPsec VPN

  Correct Answer: AC