Symantec Symantec Certifications 250-253 Questions & Answers

• Question 171:

  The service group named websg is currently online on the sym3 node. All other nodes are running.

  Consider the following partial main.cf definition:

  Group websg (

  SystemList = { sym1=0, sym2=1, sym3=2 }

  AutoStartList = {sym2, sym3 }

  FailOverPolicy = Priority

  )

  The operator incorrectly shuts down a critical resource in the websg service group outside of Veritas

  Cluster Server.

  Based on the information provided, what will happen to the websg service group?

  A. It will remain partially online on the sym3 node.

  B. It will switch to the sym1 node.

  C. It will switch to the sym2 node.

  D. It will restart on sym3 node.

  Correct Answer: B

• Question 172:

  Consider the following configuration:

  group websg (

  SystemList = { sym1 = 1, sym2 = 2 }

  AutoStartList = { sym1 }

  Frozen = 1

  )

  While websg is online, all of the systems in the cluster are rebooted simultaneously. All of the systems

  finish booting and successfully join the cluster.

  What will happen to the websg service group?

  A. It will unfreeze on reboot and start on sym1.

  B. It will remain offline on all systems.

  C. It will resume its state before the reboot.

  D. It will start on sym1 in a frozen state.

  Correct Answer: B

• Question 173:

  System capacity and service group load are the main components for which FailOverPolicy?

  A. Load

  B. Order

  C. Limit

  D. Capacity

  Correct Answer: A

• Question 174:

  Which two are default behaviors of Veritas Cluster Server service groups? (Select two.)

  A. Migrate service groups from a system on intentional system shutdown

  B. Start the service groups in lexical order

  C. AutoDisable the service groups on cluster startup

  D. AutoDisable the service groups on a system when all low priority links fail

  E. Start the service groups in the order of the attribute SystemList

  Correct Answer: AC

• Question 175:

  Which service group attribute enables specifying preferred nodes for failover?

  A. SystemZones

  B. AutostartList

  C. ClusterList

  D. IntentionalOnlineList

  Correct Answer: A

• Question 176:

  Which three statements apply to communication between the Enforce Server and detection servers? (Select three.)

  A. By default, the Enforce Server and the detection servers communicate over port 8100.

  B. Port 3389 must be open between the Enforce Server and the detection servers.

  C. The same port number must be used for all detection servers.

  D. The servers can be configured to use any port higher than 1024.

  E. IPSec must be configured on the Enforce Server and the detection servers.

  Correct Answer: ACD

• Question 177:

  An application is experiencing failures. The application administrator wants Veritas Cluster Server to take all resources offline after failure. The application should remain offline.

  Which attribute can accomplish this?

  A. ManageFaults

  B. FailOverPolicy

  C. AutoFailover

  D. Critical

  Correct Answer: C

• Question 178:

  Refer to the following service group example:

  group websg (

  SystemList = { sym1 = 0, sym2 = 1 }

  AutoStart = 0

  AutoStartList = { sym2 }

  )

  DiskGroup webdg (

  DiskGroup = webdg

  )

  IP webip (

  Device = eth0

  Address = "169.254.128.12"

  NetMask = "255.255.255.0"

  )

  Mount webmnt (

  MountPoint = "/web1"

  BlockDevice = "/dev/vx/dsk/webdg/webvol"

  FSType = vxfs

  MountOpt = rw

  FsckOpt = "-y"

  )

  NIC webnic (

  Device = eth0

  )

  Application webproc (

  MonitorProgram = "/usr/local/bin/web -monitor"

  StartProgram = "/usr/local/bin/web -start"

  StopProgram = "/usr/local/bin/web -stop"

  )

  webip requires webproc

  webproc requires webmnt

  webip requires webnic

  webmnt requires webdg

  Which resource will start online last?

  A. webip

  B. webmnt

  C. webproc

  D. webdg

  Correct Answer: A

• Question 179:

  Where can an incident responder view all actions that have occurred for an incident?

  A. Incident Snapshot

  B. Auditlog Table

  C. Incident Actions

  D. System Events

  Correct Answer: A

• Question 180:

  How can a system administrator obtain the log files for a detection server? (Select three.)

  A. Run the Log Collection Utility (LCU)

  B. Navigate to the logs directory

  C. Click Fetch Latest on the Server Detail page

  D. Select Logs under Administration node

  E. Download logs from the System Overview page

  Correct Answer: ABC