Free E20-690 Exam Dumps Preview

Which part is a Customer Replaceable Unit?

Where can you obtain the VNX Procedure Generator?

A user is manually configuring the Control LUNs for a VNX gateway attached to a Symmetrix.

What is the required size for LUN 5?

What are the Alert Severity Types?

Which statement applies to the VNX w/MCx (VG10 and VG50) Gateway configuration?

When installing a VNX for File, which subnet must be used?

A new client unfamiliar with Unisphere suspects a fault condition on a VNX system.

What can they use to determine a fault?

Refer to the exhibit.

You are onsite to replace a faulted Data Mover within a VNX8000 and note the following: The storage administrators have received alerts that Server_6 has faulted but Server_6 now appears online.
Server_3 is configured as a standby for Server_2
Server_7 is configured as a standby for Server_6

Which slot in the diagram contains the active data mover Server_6?

What is a function of the ESRS Management Utility?

When should an SP's non-maskable interrupt button be pushed?

In addition to VNX Installation Assistant, what other tools and methods are available for VNX registration?

Refer to the exhibit.

From the highlighted information in the picture, which type of I/O module is represented?

Refer to the exhibit.

When using the VNX Procedure Generator to make a hardware replacement procedure, what will be the results of selecting the indicated link?

What does the naviseccli managefiles command with the -list function display?

You are on a customer site to perform a software upgrade on a VNX Unified storage system. You have worked with the customer to install USM on the system that has IP connectivity to the VNX system and the Internet.

What is the behavior of the Download Software Updates Wizard in USM?

What is the recommended corrective action to take if a mistake was made during initialization of a VNX Unified array?

Which types of storage arrays are supported on a VNX gateway system?

You are onsite for a DAE and drive upgrade for a VNX 5800 array. After inspecting the collections from the array you notice that the VNX has the following active configuration:

1 x 2.5" DPE
21 x 2.5" DAE's
10 x 3.5" DAE's
681 bound data and hotspare drives
0 faulted drives
2 unbound drives

How many additional 2.5" DAEs and drives can the array support?

A customer wants to use compression, deduplication and thin provisioning.

Where are the software enablers located?

What is the minimum EMC-recommended ratio of standby Data Movers to production Data Movers?

What is the VNX default failover policy for a Data Mover?

On VNX Unified series X-blade, which is the correct cabling configuration for the 4-port 8 Gb FC I/O module in slot 0?

In a VNX for File system, what is connected to the Control Station Eth1 port?

Refer to the exhibit.

The engineer needs to manage a VNX system during an unplanned data center outage but the network is down.

Which connection(s) on the SPE management module can be used?

You are an EMC service provider and want to install the ESRS IP client solution. The workstation on which you want to install this software is on a network with a proxy server.

What information must you provide in order to be able to install the solution?

Dump files are needed from a Storage Processor.

Which naviseccli managefiles command option will accomplish this?

Refer to the exhibit.

Which port would be used to connect a secondary Control Station?

You are about to install a VNX7600 Unified.

Which components should be on-site and installed?

When using USM to download software updates, what is the default location where the software is stored?

What are the minimum components required to configure a VNX5500 for Block storage system?

Refer to the exhibit.

What is a function of the IPv6 Common Parameters configuration type?

You are upgrading the VNX OE for File to a new version and choose to reboot the Data Movers during the upgrade.

How long will the users lose access to their files?

An operator must shut down the standby Control Station CS1 on a VNX configured with dual Control Stations.

What action, if any, does the operator need to take to allow management and monitoring of the VNX to continue when CS1 is offline?

After a new VNX 5400 was installed and powered up, the Data Movers are continuously rebooting. It has been determined that a cabling issue is at fault.

Which configuration should be checked first as the most likely cause?

On which LUN will SP software driver packages be transferred when using the NDU command?

You are changing the SP hostnames using the storage system Initialization Wizard.

What message will be displayed?