VCEdump

DES-4121 PowerEdge Specialist for Implementation Engineer

PDF question preview Back to product

Reading controls

Reader tools

Free demo

9 of 60 questions

Purchase the full version to unlock every question and answer.

View the full question set

Preview tools

Try Web TestEngine

Question formats

Single choice9

EMC · DES-4121

Free DES-4121 Exam Dumps Preview

Preview real exam questions, verified answers and available explanations before choosing a study plan.

Question 1

Single choice

A technician replaces a faulty system board on a server.
In addition to powering on the system, what step must the technician take to install the correct service tag?

A
Type asset <asset tag> to change the asset tag
B
Login in to the iDRAC
C
Press F11 to start the Boot Manager
D
When prompted by Easy Restore, press Y to restore the Service Tag, license, and diagnostics information

Reveal answer details Close answer details

Correct answerD

Explanation

Reference
https://cc.cnetcontent.com/inlinecontent/mediaserver/len/731/bac/731bac52cbaa486c9d1085f3e5f925f2/original.pdf

Question 2

Single choice

A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. They also create a global hot spare. A drive fails on the second virtual disk.

What is the result?

A
Dedicated hot spare for the virtual disk replaces the failed drive.
B
Global hot spare replaces the failed drive.
C
Copyback operation occurs between the failed drive and the dedicated hot spare.
D
Copyback operation occurs between the failed drive and the global hot spare.

Reveal answer details Close answer details

Correct answerB

Explanation

Refe
https://www.dell.com/support/article/pk/en/pkbsd1/sln305775/dell-poweredge-how-to-assign-a-hard-drive-in-global-hot-spare-?lang=en

Question 3

Single choice

A technician is completing initial firmware updates on a server. One of the updates is a power supply update. During the update process, the server powers off. When the technician hits the power button, they do not see any response from the server.

What is the cause of this issue?

A
Server lost power
B
Control panel or power button failed
C
Front power button is not operational during an update; the technician should use the rear power
button.
D
PSU firmware may now be corrupted

Reveal answer details Close answer details

Correct answerD

Question 4

Single choice

A technician deletes the iDRAC Express license on a R440 server.

Which license type is then enabled?

A
iDRAC Express license cannot be deleted
B
iDRAC Basic license
C
iDRAC Enterprise license
D
iDRAC will not have a license until a new one is installed

Reveal answer details Close answer details

Correct answerB

Question 5

Single choice

A technician is configuring a PowerEdge R640 that has two PSUs. The rack in which it is being installed has two power distribution units (PDUs). No high power such as GPUs are required. The user wants as must redundancy protection as possible.

What is the best way to configure the PSUs?

A
Redundancy Mode set to 2+0 with each PSU power cord connected to a different PDU
B
Redundancy Mode set to1+1 with both PSU power cords connected to the same PDU
C
Redundancy Mode set to 1+1 with each PSU power cords connected to a different PDU
D
Redundancy Mode set to 1+0 with the second PSU stored nearby for quick replacement if the first PSU fails

Reveal answer details Close answer details

Correct answerA

Explanation

Reference
https://serverfault.com/questions/809363/load-distribution-across-psus-on-a-dell-poweredge

Question 6

Single choice

A server has two power supply units (PSUs) in a redundant configuration. One PSU fails. A technician replaces the failed PSU, but the server does not return to redundant power mode.

What is the cause of this issue?

A
Power redundant option is disabled in the System Setup Utility.
B
Server has not been power cycled to bring the new PSU online
C
Both PSUs were not replaced at the same time
D
New PSU has a different wattage than the existing PSU

Reveal answer details Close answer details

Correct answerB

Question 7

Single choice

A technician needs to add a device to SupportAssist Enterprise. Policy requires that no additional software be installed on the server OS.

In addition to Username and Password, what information is required to add the device?

A
IP address or hostname for the server OS
B
IP address for Dell TechDirect
C
IP address fir OpenManage Server Administrator
D
IP address or hostname for the iDRAC

Reveal answer details Close answer details

Correct answerD

Question 8

Single choice

A technician is setting up a previously used server. Upon power up, the PERC alerts them to the presence of a foreign configuration. In the iDRAC storage section, the technician checks Foreign View. The foreign array configuration is the same as the configuration needed for the new project.

What is a recommended way to prepare the disks for the new project?

A
Edit the foreign configuration and set it to Ready
B
Import the foreign configuration and perform a full initialization
C
Format the foreign configuration and clear the controller configuration
D
Access the Ctrl+R utility, clear the foreign configuration and set up array as needed

Reveal answer details Close answer details

Correct answerD

Explanation

Reference
https://www.dell.com/community/PowerEdge-HDD-SCSI-RAID/PERC-H310-active-drives-are-listed-in-foreign-config/td-p/6126153

Question 9

Single choice

A technician plugs in a server that has dual power supply units. After powering on the system, they notice that the power supply status indicators blink green then turn off.

What troubleshooting steps should the technician take to resolve this issue?

A
Set the power supply redundancy option to `No Redundancy'
B
Check that the PSUs are not connected to a 240VAC source
C
Update the iDRAC firmware to enable control of new PSU features
D
Check that the PSUs are the same efficiency, feature set, health status, and supported voltage

Reveal answer details Close answer details

Correct answerD

Explanation

Reference
https://qrl.dell.com/Files/en-us/Html/Manuals/R630/Power%20indicator%20codes=GUID-FBD2281B-1608-4FF8-9AFE-4E33BB6FF810=1=en-us=.html

Free DES-4121 Exam Dumps Preview

PowerEdge Specialist for Implementation Engineer

PREVIEW CONTENTS · 1 VOLUME

QUESTION 1

QUESTION 2

QUESTION 3

QUESTION 4

QUESTION 5

QUESTION 6

QUESTION 7

QUESTION 8

QUESTION 9