Free CWDP-304 Exam Dumps Preview

You have initiated a site survey to be performed and the team has been onsite and is halfway through gathering the necessary data. The project sponsor just asked you to make sure the WLAN supports radio frequency identification (RFID) location tracking. How would you possibly characterize this situation?

Response:

A controller-based WLAN infrastructure has its controller on a different subnet than its APs.

What device must be used to enable any communication between the Controller and the APs?

A museum wants to offer Wi-Fi to its visitors. One of their requirements is to have the APs blend into the design of the museum. What should you do to meet this requirement?

Response:

After successfully deploying and validating a WLAN intra structure, who should be trained for a better understanding and management of the solution? (Choose the single best answer)

When creating a long-distance bridge link, it is important to know the channels in use by other networks on both ends of the link and within a reasonable range It is not as Important to know the channels in use in the middle area of the link.

Why is this the case?

An amplifier has a 1 dB compression point of 32 dBm and a gain of 20 dB.

Which is the highest average input power shown here that would be safe to operate a 24 Mbps 802.11g signal so that spectral regrowth is not a problem?

Response:

Aesthetics are very important in some environments.

What common installation technique can be used to best meet this requirement in a stadium?

What are the best practices for belter location accuracy when deploying Wi-Fi RTLS?

What functions may be performed by a WIPS?(Choose all that apply.)

Response:

What document should be created that provides instructions for install technicians to mount and configure APs?

You have determined the best mounting locations for APs in a given installation. The facilities manager has asked you to change the locations for several APs due to aesthetic concerns. You suggest mounting the APs in the ideal locations and painting them so they go unnoticed in the environment.

What is a valid recommendation or consideration when painting APs?

What are some common problems with short (12 or fewer characters) ASCII passphrases in WPA/WPA2-
Personal networks?

Response:

Who should be in the final meeting from the customer-side after successfully implementing a WLAN infrastructure?

An engineering firm just upgraded their WLAN form nine 802.11n APS to nine 802.11ac APs. After this upgrade, they did not see any improvement in throughput. What is the most likely cause of this result?

Response:

If you choose to recommend dynamic channel assignment for the APs in your WLAN design what action should you also recommend'?

While configuring your site survey software for an upcoming manual survey project, you notice the configuration option for "Network Card Simulation".

What is the purpose of such a feature and when would you use it?

What limitation exists when WMM is not enabled on an 802.11n WLAN?

You have enabled IEEE 80211 FT in your WLAN infrastructure.

You want to verify roaming between APs (two at a time) and determine If all of your end-points are capable of performing fast roaming What tool would you use to achieve this goal?

Which of the following items could be considered constraints when performing a network design?(Choose all that apply.)

What single tool, by design can be used to verify channel selection, encryption in use and number of APs above a specified signal threshold in a given location during deployment?

One of your customers plans on providing wireless coverage to a warehouse facility. After performing an initial walkthrough, you collect the following information:

The central part of the warehouse is between 400 and 600 feet (122 to 183 meters) from the warehouse switches mounted on the walls.

# The warehouse storage is composed of metallic racks with varying inventory levels and contents, from electronics and plastic toys to food pallets and juice bottles. # Workers need basic data coverage from their working location, and are not highly mobile. They usually work from one single aisle, and their laptop is on a cart with wheels.

What would be your one recommendation to provide coverage to the central area of the warehouse?

During a post-validation assessment, you have configured a client for 802.1X/EAP but it is not passing authentication. Which areas should you check in the WLAN configuration?

Response:

ABC Company has a WLAN controller with 10 controller-based APs; the Voice SSID is configured for
centralized data forwarding. Each AP is connected to an access port on a layer-2 Ethernet switch. Each layer-2 switch is uplinked to a single layer-3 core Ethernet switch. The WLAN controller is connected directly to the layer-3 core Ethernet switch. Layer-3 tunnels are created between all controller-based APs and the WLAN controller. A voice server is connected to the layer-3 Ethernet switch.

When a voice-enabled QoS STA sends an IP data packet to a voice server in this scenario, the DSCP value carried in the STA's IP data packet gets mapped to what and by which device?

You are working on a VoWLAN design with your customer's wired networking team.

How many distinct priority levels do you expect for the voice applications?

When deploying APs outdoors, what additional component needs to be used that is not needed indoors?

What service must be implemented on your customers' network to authenticate users against an LDAP database prior to access to the WLAN infrastructure being granted?

Which type of building material causes the most attenuation of Wi-Fi signals'?

In a convention center, you have received complaints about the WLAN infrastructure. At this moment, the are only two APs in one auditorium.

After analyzing the situation, you determined that there are more client devices that the infrastructure was designed for. There are only two APs to support more than 300 devices using the Wi-Fi at the same time.

What should you do to make the Wi-Fi work as expected?

Response:

What is the most suitable antenna option to be used when designing a WLAN infrastructure with APs mounted on a ceiling with a height of more than 20 feet and having all of the client stations used from the floor?

Looking at a client radio specification sheet that states Receive Sensitivity of #82 dBm @ 18 Mbps would mean:

Response:

What is a typical characteristic of barcode scanners?

When designing a static channel plan for an office using voice devices near an airport, which range of channels should be avoided to ensure optimal performance when implemented?

You are validating association capabilities from clients to an 802.1X/EAP secure SSID. The RADIUS server's IP address is 10.100.50.25 and the default RADIUS authentication port is used. When testing them, none of the clients are able to associate to the SSID. Troubleshooting the WLAN infrastructure, you found out that the server is up and the RADIUS service is up as well, but the authenticator is not able to communicate properly with the server.

What's your next troubleshooting step?

Given: As the wireless network administrator for XYZ Company, you are planning to upgrade your aging wireless network infrastructure, as well as some clients, to support 802.11ac.

In your research, you have discovered that your new wireless client devices and infrastructure are 802.11ac, WMM, and WMM-PS certified by the Wi-Fi Alliance. Some of your existing client devices are 802.11a/b/g devices that do not support WMM.

Given this information, what scenario is possible when your company's employees begin using both types of client devices on the new WLAN?

Response:

You told your customer that multipath fading may be mitigated simply by moving one or both of the receivers antennas a small amount, usually by one to four wavelengths away from its original position.
Your customer is prepared to make the change, but does not know the wavelength for 802.11ac.

What is the approximate wavelength of an 802.11ac radio wave?

The thermal noise is at #174 dBm/Hz. A spectrum analyzer has a resolution bandwidth of 1 kHz and a 5 dB noise figure. What is the level of the noise floor?

Response:

Assume that your network operates in a regulatory domain that allows use of the entire 5 GHz space allowed in the 802.11ac amendment. In your upcoming

802.11ac deployment, you would like to take advantage of the performance improvements that result from channel bonding. However, after extensive testing, you have determined that your mission-critical WLAN should not use channels requiring DFS support.

Given those two criteria (enable channel bonding and disable DFS channels), in the 5 GHz spectrum, how many non-overlapping 40 MHz channels will your system be able to use?

When implementing multiple SSIDs to what is each SSID typically mapped in order to provide traffic management separately for each SSID?

As you plan a WLAN upgrade, you have assessed the network requirements and data signatures of your applications. One of the popular applications used on your network requires high bandwidth and low to medium Wi-Fi loss, but can tolerate moderate latency and jitter.

What application matches this description?

Location technology (RTLS) can use which of the following methods?(Choose all that apply.)

Response:

What part of the 802.11n preamble is used by the receiver to estimate the spatially multiplexed signal channel? What mode is this used in?

Response:

In most WLAN design tools, after defining project parameters or during the project creation wizard what action will you take before you can begin the actual design process?