Free CPIM-MPR Exam Dumps Preview

Which tactic would successfully reduce cycle stock?

Which of the following plant is used in the production process, where few raw materials can be made into several end products?

As used in material management, bill of material:

Each of the following actions would reduce safety stock levels EXCEPT:

What is done by individual worker who, instead of checking for defects, checks for errors that will cause defects?

is the most detailed, complete and accurate of the capacity planning techniques.

Which business process is concerned with the replenishment of items and usually occurs on a weekly basis?

What is used to calculate how long it will take to complete a task?

Production activity control in intermittent manufacturing is complex Because of:

Where-used reports give information about

The capability of the process is a measure of specifications limit.

For a particular commodity, the line-haul cost is $2.50 per mile. For a trip of 500 miles and a shipment of 600 cwt., what is the cost of shipping cwt.? If this shipment is increased to 1000 cwt., what is the saving in cost per cwt.
?

Extranet is an internet shared by two or more companies.

Today production control works in a demanding environment shaped by six major challenges.

Which one of the following is not of those challenges?

Which of the following best describes JIT?

describes the function of the organization.

A planned order receipt is generated by MRP when:

The group works together to develop the product design so it meets the needs of the customer and can be made and delivered to the customer at low cost in a process called:

The step for preparing MPS is/are:

The line between two or more supply sources where the laid-down cost is the same is known as:

Stock, from which withdrawals are made, can be located close to the marshalling and shipping area is referred to as:

Production management is concerned with:

Which forecast performance measure detects bias?

Altering the load in balancing capacity available means?

Functional specification can be described by a combination of:

Which of the following are the two sources of specifications?

The concept in which to preplan and generate schedules but instead to react to the final customer order and produce only what is needed to satisfy demand and then only when it is needed, is known as:

Knowing the quantity beyond which the cost of using method B becomes less than for method A enables us to decide easily which process to use to minimize the total cost, this quantity is called:

In s distribution system, which activity affects customer service and the cost of providing it?

As 1980 gave way to the 1990 the world continued to change, forcing additional changes in supply-chain

concepts. All of the following statements depict those changes EXCEPT:

Operations management works in a complex environment affected by many factors. Among the most important are:

Some of the characteristics customers expect when they buy products are all of the following EXCEPT:

People should not only be trained in their own jobs but should also be cross-trained in other skills and in problem solving techniques, in order to achieve:

The flow of work centers must be planned to meet delivery dates which means production activity control must do the following:

Means to find ways to increase the available hours of the constraint, including more of it is referred to as:

Economic regulation has centered on which of the following areas?

Once the preliminary production plan is established, it must be compared to the existing resources of the company. This step is called answered: Are the resources available to meet the production plans?
If not, how will the difference be reconciled?

According to the Theory of Constraints, which of the following statements is true?

The process of determining in detail the amount of labor and machine resources needed to achieve the required production id known as:

Which of the following strategies is most likely to produce the shortest delivery leadtime?

The information for quantities required in manufacturing, planning and control system will come from all of these EXCEPT:

It takes capacity planning to the next level of detail .The master production schedule is the primary information source.

What is it?

Which of the following is the characteristic to flow manufacturing?

The capacity planning process occurs at each level in the priority planning process, varying only in:

A routing file should exist for every component manufactured and contain which of the following information?

What the following figure shows:

Work done at each workstation should take about the same time, this is called:

It is virtually impossible to be the best in every dimension of competition. Firms should in general:

A work center is to process 150 units of gear shaft SG 123 on work order 333.the setup time is 1.5 hours, and the run time is 0.2 hours per piece.

What is the standard time needed or run the order?

The systematic use of techniques that identify a required function, establish a value for that function, and finally provide that function at the lowest overall cost, is known as:

Operational splitting is practical when:

A guide for all in the organization about how products and services should be provided is known as:

Which scheduling is concerned with production activity from the present to a few months ahead?

What is concerned with removing work content, not with spending money on better and faster machines?

Planned order receipt is generated by MRP when:

Frozen zone, slushy zone and liquid zone are the part of

shows the quantities needed and when manufacturing intends to make use or use them.

To check the feasibility of the master Production Planning, provide warnings to any bottlenecks; ensure
utilization of work centers and advice vendors of capacity requirements is the purpose of:

This is the situation of lead time strategy in case of:

A company wants to minimize the cost of manufacture and also be flexible enough to adapt to changing needs. Changes to production schedules can result in the following EXCEPT:

A structured approach to organize the operation for more effectiveness and less waste that is the overall goal of a lean production system includes which 5S?

Benchmarking includes the following steps:

In terms of structure and function, the construction supply chain is characterized by the following element/ s:

What exist because of the time needed to move goods from one location to another such as from a plant to a distribution center or a customer?

Which of the following one is the method of reducing system nervousness?

A tracking signal can be used to monitor the quality of forecast.

Items purchased or manufactured in quantities greater than needed immediately create .

Purchasing and production activity control:

demand or lead time. is held to cover random unpredictable variations in supply and

A company ships a particular product to a market located 1000 miles from the plant at a cost of $4 per mile. Normally it ships 500 units at a time. If the company can ship the units unassembled, it can ship 800 units in a truck.

What is the line-haul cost per unit now?

Material Requirements Planning (MRP) is:

The costs those directly associated with the amount produced or sold are called:

An income statement of a company is as follows:

If through a well-organized materials management department direct materials can be reduced by 10% and direct labor by 5% the improvements in profits would be:

A work center working one 8 hour shift for 5 days a week is available _____________ hours a week is available

The operation that controls the work feeding the bottleneck and must operate at a rate equal to the utput of the bottleneck so the time buffer queue is maintained is known as:

What have most of the values clustered near a central point with progressively fewer results occurring away from the cluster?

Using non-cumulative methods, what is the ATP in period 1?

All of the following are requirements for a successful employee involvement (EI) program EXCEPT

An SKU costing $10 is ordered in quantities of 500 units, annual demand is 5200 units, carrying costs are 20%, and the cost of placing an order is $50. Calculate annual inventory carrying cost

What means doing it right the first time and, if something does go wrong, stopping the process and fixing it?

In the previous problem how much actual time will be needed to run the order if the work center has an efficiency of 120% and a utilization of 80%?

If a company makes wooden tables, the demand for the tables is called

To provide the required level customer service, to minimize the costs of transportation and handling, and to be able to interact with the factory to minimize the scheduling problems are all objectives of:

"Framework of organizing, defining and standardizing the business processes necessary to effectively plan and control an organization so the organization can use its internal knowledge to seek external advantage"
This is the definition of:

If there are 20 as in stock, only 30 needs to be made, then the requirements for components parts would be:

Which of the following is NOT the class of activity?

Gather the information needed by the shop floor to make the product. Release orders to the shop floor as authorized by the material equipment plan. This is called dispatching. Production activity control will do such things in:

Master scheduling tries to level capacity and just-in-time tries to level the schedule based on capacity and material flow.

The workstations required to make the product, or family of products, are located close together and in the sequence needed to make the product is called: