Free CLSSYB Exam Dumps Preview

The purpose of a ______________ is to identify the complexity of the process and to assist in identifying critical steps in the process.

For the data shown here a Belt suspects the three grades are supplying the same results.

Which statement(s) are true for proper Hypothesis Testing?

SIPOC stands for Suppliers, ___________, Process, Output and Customers.

Stability, Bias and Linearity define the ___________ of a Measurement System.

Common and _____ Cause Variation are the focus of Statistical Process Control.

The Control Plan is created following the finalization of the Measure Phase and can be closed when?

Which element of waste best refers to "having to fix a defect"?

Upon completion of a project a Belt must complete the ____________________ then transfer responsibility for this to the Process Owner.

Following have been exponents of Quality evolution except:

As we attempt to find a commonality of terms to assess the performance of a broad range of processes we use a key metric called the DPMO which stands for __________________________?

A Six Sigma tool that helps to screen factors by using graphical techniques to logically subgroup multiple discrete X's plotted against a continuous Y is known as a _____ Chart.

One of the primary benefits of your team working together to create an X-Y Diagram is that the data collected from this exercise is accurate and certain.

A Macro Process Map may map a process showing the entire activities of a department and can likely be broken into many Micro Process Maps showing numerous processes that comprise the activities of the department.

Which statement is incorrect about Fractional Factorial Designs?

Y=f(X), with this what should we focus on "Y" or on "X":

As we begin to describe the things occurring with our process through a Process Map we begin to see some steps that are NVA which stands for ____________.

The RPN or Risk Priority Number is used to rank the various Failure Modes as to their impact on the output of the subject process.

Control Charts were developed by Dr. Shewhart to track data over time.
To detect Special Cause variation the Control Charts use which of these?

In Control chart interpretations, how many business rules (Shewart Rule's) will be used to interpret for stable process.

Who is responsible for adherence to the Monitoring Plan?

In order to properly draft a Process Map at the start of a project we are told to __________________ from beginning to the end.

Quality and the Critical-to-Quality (CTQ's) are both subjective terms that are defined by the _____.

As a type of measurement error, Linearity describes the deviation of the measured value from the actual value.

When a Belt decides to use written procedures and visual controls to improve the consistency of the tasks that must occur in the process he is improving he has utilized the _____ activity of 5S.

An important factor in a viable _________ is to determine who, when and to what level various personnel must be trained to maintain the improvements made to a process.

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

There are a large number of potential human errors.

What are possible countermeasures for inexperience?

What is Six sigma?

What is the Probability value of the area under the curve between -1.0 and -2.0 Standard deviation units in Normal Distribution?

Cost of Poor quality (COPQ) does not include:

Six Sigma is a term used to indicate that there are 6 Standard Deviations below and above the process Mean and within upper and lower specification limits.

For Six Sigma, the period of evolution started from:

An ANOVA used across many dependent variables could increase the Beta risk.

The traditional methods of obtaining customer information could also include:

Which of these might contribute to similar distributions having Unequal Variance?

A _____ is used primarily to track the stability of the average value of a metric of interest.

After reviewing the Capability Analysis shown here select the statement that is untrue.

In your project, Review effort (hrs, X) and defect rate (no. of defects per hour, Y) show a negative correlation. It means:

An unbiased true value which is normally reported as the difference between the average of a number of measurements and the true value is called:

Multiple Linear Regressions (MLR) is best used when which of these are applicable?

You are a Project Manager wanting to compare on time delivery (%) of Team Leads across 4 teams, your choice of technique would be?

_____________ represents all the variation that one can expect to experience from the output of the subject process.

Following the completion of a LSS project the Belt not only creates a Control Plan he also develops a _____ so those involved in the process know what to do when the critical metrics move out of spec.

_____ helps to understand Process behavior for parametric distribution.

Process Capability is defined based on customer requirements, defect free performance and output over time.

When a process has proven itself to function at a Six Sigma level this means there are less than 3.4 defects per ___________ opportunities.

Kanban establishes a means of monitoring production, conveyance and delivery information such that efficient flow is established. The method used by Kanban is to require a _____ before anything moves.

Run charts can be understood by the following:

Which one of the following is not a Process Improvement Methodology?

Which of the following would likely be a CTQ (Critical-to-Quality) for the purchase of a service?

A Belt experienced an Alpha of .05 and a Beta of .10 and knew these are the most common risk levels when running a Statistical test.